Refer to the figure, what is the vertical reaction of support D in kN? 8 kN 8 kN -2 m- m 3 kN/m B 4 m D 3 m 10.17 14.83 10.25 O 1.75

Q: Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1.…

A: Given: Required: shear and moment at the left of C  shear and moment at the right of C

Q: Draw the bending moment diagram of the system under the influence of external loads below. Calculate…

A: (a) Draw the bending moment diagram of the system under the influence of external loads below. (b)…

Q: Draw the bending moment diagram of the system under the influence of external loads below. Calculate…

A: (a) Draw the bending moment diagram of the system under the influence of external loads below. (b)…

Q: 3 kips/ft | 4 kips B C D A – 4.5 ft– +3 ft→

A:

Q: a) Determine the support reactions at A and B, if /is equal to 50 N/m. b) What should be the value…

A:

Q: 17 Refer to the figure, what is the reaction at pin C in kN? (2 0.75 kN/m 1.5 m 12 kN D 1.5 m- 2.5 m…

A:

Q: Draw shear force and bending moment diagram by using graphical method. 80 kN/m 6 kN/m 4 m 1.5 m RA…

A: Draw SFD and BMD

Q: Determine the horizontal force reaction at joint 1. A-9.12 in. 1-375 in. 21 A= 10.3 in 1-285 in. 1…

A: Given:- tanθ=2010θ=63.43oInclined length of the member 1-2=202+102…

Q: Calculate the minimum force P required to keep the 0.294 KN rod AB from sliding. The contact surface…

A:

Q: Solve for: 1. Maximum W in kN if each leg resist 10.098 kN. 2. If W is 49 kN. what is the force…

A: ##Solution of given problem part1, 2, 3 of mechanics ###3d vector forces##

Q: WIn the figure 9, assume clockwise moments as positive, force F= 432KN and force P =500 KN. Compute…

A:

Q: Q3/. Determine the components of the force acting parallel and perpendicular to the pipe AO.

A: Force component, F⇀ = F uAB⇀ Where F = 500 N uAB⇀ = Unit vector in the direction AB         =…

Q: FORCES, RESULTANT & ΜΟΜΕNT 90 F1 76 DEG 2. The forces shown in the figure are directed at the…

A:

Q: Determine the reactions at support and the forces acting on each member. By applying 1 unito load…

A:

Q: Determine the Maximum absolute shear from the shear diagram. Attach here the shear diagram and…

A:

Q: FORCE SYSTEM IV. EQUILIBRIUM OF NON-CONCURRENT Example Problem 2: A 12-ft bar of negligible weight…

A:

Q: 7.5 kN C 1.0 m-1.0 m 0.5 m 5.0 m 1.8 kN/m -3.0 m B 900 A simply supported beam is loaded as shown in…

A:

Q: In the figure 9, assume clockwise moments as positive, force F= 432KN and force P =500 KN. Compute…

A:

Q: A girder and floor beam constrcution subjected to concentrated loads is shown in Figure . Draw the…

A:

Q: Topic: EQUILIBRIUM OF A RIGID BODY Show free body diagram & Direction of the equilibrium equation…

A:

Q: Determine the reactions at support and the forces acting on each member. By applying 1 unit load…

A:

Q: Bending moment diagram and M=M(x) equations for the following system.

A: To draw SFD and BMD

Q: I. Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I=70(10%)mm*. Use…

A:

Q: Determine the vertical reaction at E for the beam shown using the slope-deflection method. 20 kN/m…

A:

Q: Q.3) For the figure shown, if the moment of the force F about the axis BC is 150 lb ·ft. B Determine…

A: Determine the position vector for the force F.…

Q: 3. A 400N weight is suspended by two cables connected to a trss. The center of gravity of the weight…

A: Determine the magnitude of forces at BC and BD

Q: Solve using FEM stepwise O 4,E 2 2 Р

A:

Q: Determine the member force CD (kN) shown in the figure. 3 KN 2 m 45° 130 30 2 m 2 m

A:

Q: The sector gate UE is submerged in water as shown in the figure. The sector gate is one-twelfth of a…

A:

Q: Problem II. Solve the problem using Conjugate Beam Method. The beam shown has a constant El and is…

A:

Q: 100 kN 100 kN (4000 mm?) 75 kN - (5000 mm) 3 m (5000 mm?) A B (4000 mm) 4 m E = 200 GPa (4000 mm)…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.