Refer to the circuit below |F Z₁ = 39 +17₁ Z₁ = 1+j1 A 1 24010 @ 1240/120 240/120 ZT ZT B ZT What is the magnitude of the load current? express answer in amperes ZLA zu

Q: 10 minute presentation on Tidal renewable energy

A: Tidal Renewable Energy PresentationSlide 1: IntroductionTitle: Harnessing the Power of Tides: An…

Q: write the ontpul wavefarm of the given IGBT based single - phase systen! Ib Lo 1eattery Co Vo K2

A:

Q: A varying phase shift produces a(n)_

A: The term phase shift means changing the phase. It may be time point of view or it may be magnitude…

Q: Write the correct answer If the peak to peak voltage is equal to 10. How much the RMS value of the…

A:

Q: Q27-A (ii) How can solar power plants kill the birds?

A: Solar power plant kill birds is seen nearly many times according to the many surveys. According to…

Q: Derive star to delta transformation

A: we need to derive star to delta transformation

Q: Identify the effect of the power coefficient for a wind turbine if the power extracted by rotor…

A:

Q: An atom consists of: Please choose one: a. one nucleus and only one electron b. answers B. and C.

A: According to question we have to discuss about Atom.

Q: iii. Induced emf in the coil if the current fall from 3A to 1A a. 420V b. 620V c. 0.62V d. 0.42V

A: Put the given inductor value L and change in time

Q: If the humidity of the air is increased, then output of wind energy conversion system will O a. may…

A: Humidity -> It is the amount of water Vapour present in the air. The wind energy output from the…

Q: Lightning over-voltages and switching phenomena of switchgears are two examples of transient…

A: Lightning surge: A lightning surge is a very short burst of high voltage which if not suppressed can…

Q: 14. A 240 V, 25HZ sinusoidal generator is connected to a 20 ohms resistor. Determine the…

A:

Q: E-06, PC-05. An induced current in a coil? Does not affect the EMF producing it. Aids the EMF…

A:

Q: R= バニスル | कि-30-

A:

Q: If the peak to peak voltage is equal to 10. How much the RMS value of the voltage? T TT Arial 3…

A: VP-P = 10 V So VP = VP-P = 10/2 = 5V

Q: IDm ALOO 100s2 Ikse

A: In the given circuit the three impedances 1000ohm, j100ohm, -j4ohm  are in parallel. We will first…

Q: 14 If the induction electrical machine operates at slip s = - 0,1 the mode of operation is * O…

A: The answer is Generator

Q: Q29. As the field voltage increases, the de motor's speed

A:

Q: When will the VAR - hour meter disc rotate in one direction for a lagging current and in the…

A: In this question we need to choose a correct option

Q: Quiz; An alternating current of frequancySoHe has makimum Value of (I 20A). write the instantanous…

A: Given : Freq = 50 HZ Imax =Io = 120A ω=2πf

Q: An alternating voltage, given by v = 100 sin 314t is connected in series with a diode. The average…

A: Given data, V=100sin314t

Q: For a three blades horizontal axis wind turbine the blade tip speed is more than the wind speed.…

A: Ans :- True  Explanation:-  What is tip speed ? It is a distance that selected point on peripheral…

Q: Quantitative Analysis Figure 1: Monthly returns ACF Do the returns look like white noise? Explain

A: Given the graph of an auto-correlation function as shown below: We need to explain whether the…

Q: What is the nodal voltage?

A: Given: To answer what is nodal voltage?

Q: A conductor carries an instantaneous current i = 3 cos377t amperes. What is the average current over…

A: Given data  Instantaneous current i = 3 cos (377*t) Amp Time t1=0 t2= 6 T = t2-t1= 6-0  T = 6

Q: A low duty cycle will indicate; Low peak power  High Average power  Low Average power  High…

A:

Q: Can you explain the given questions in an original way? Compound Generators

A: As per Bartleby guidelines we are allowed to solve only one question, since these parts are…

Q: with in 10 ahmresistor and A capacity of an 120NF are Circult. acapacitor Connec ted g00 -yolt a)…

A: In this question we need to find a time constant and current in the circuit for given condition.

Q: Candela is the unit of Select one: None of these Luminous intensity Luminous flux wavelength

A: In this question we have to find out that which has unit candela...

Q: A spring balance calibrated in an environment of temperature 20°C has the following deflection-load…

A: Zero drift- it is the point where the zero reading changes under environmental conditions.…

Q: The international standard are maintained at Physikalisch Technische NPL Bureau of weight NBS

A: The solution is given below

Q: Four field coils, each with a resistance of 80 ohms, are connected in series and Supplied by a 240-…

A:

Q: Find F(-1). 2e3t sin (2t)- 3e cos (2t) Round-off to 1 decimal place. Answer: 0.8

A: In this question,   We need to determine the value of f(t) at time t= -1s

Q: A 107 hp, 257 V de shunt motor has the magnetization curve in the graph. The armature circuit…

A: Construction of D.C machines Magnetic frame or yoke Pole core and pole shoe Armature core…

Q: O 8.4853 amp

A:

Q: Assess the reasons for this drastic change in the generation fuel mix composition from 2009 to 2019.…

A: As the given pie chart shows, Coal is the largest fuel source of power generation in peninsular…

Q: In dispersion, whech colof comes in between yelow and red? O Indigo O Groan O Bue O Orange

A: Dispersion : When white light pass from the prism it splits into spectrum of color in order to…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.