Refer to Figure Q2.A tray of mass mı is supported by 3 springs as shown in Figure 3(a). The natural frequencyfa is 5.0Hz. An additional mass motor of m2 = 3.0kg (in OFF condition) is placed at the centeron top of the mass, the natural frequency is observed to be 2.5Hz.a) Calculate the mass mı.The motor m2 is ON and it rotates at the speed of 600 rpm.Calculate:a) The transmissibilityb) Attenuationc) Explain what will happen if the system run at Resonant Frequencym2m1Figure 2(a): Original systemFigure 2(b): system with m2 added

Answered: Image /qna-images/answer/acfccb12-8de0-4b8d-aed9-1ac0ef563bb6.jpg

Refer to Figure Q2. A tray of mass mi is supported by 3 springs as shown in Figure 3(a). The natural frequency fa is 5.0Hz. An additional mass motor of m2 = 3.0kg (in OFF condition) is placed at the center on top of the mass, the natural frequency is observed to be 2.5Hz. a) Calculate the mass mi. The motor m2 is ON and it rotates at the speed of 600 rpm. Calculate: a) The transmissibility b) Attenuation c) Explain what will happen if the system run at Resonant Frequency m2 m1 Figure 2(a): Original system Figure 2(b): system with m2 added

Refer to Figure Q2. A tray of mass mi is supported by 3 springs as shown in Figure 3(a). The natural frequency fa is 5.0Hz. An additional mass motor of m2 = 3.0kg (in OFF condition) is placed at the center on top of the mass, the natural frequency is observed to be 2.5Hz. a) Calculate the mass mi. The motor m2 is ON and it rotates at the speed of 600 rpm. Calculate: a) The transmissibility b) Attenuation c) Explain what will happen if the system run at Resonant Frequency m2 m1 Figure 2(a): Original system Figure 2(b): system with m2 added

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 2 Consider the blodk of mass m, connected to a spring of spring constant k and placed on a inclined plane of angle a. Let l be the length of the spring at equili brium, and a be the elongation. The block oscillates and at the same time is rotating around origin O, in the plane of the inclined, by a variable angular velocity . 1. Calculate the degrees of freedom of the block 2. What is the kinetic energy of the block 3. What is the potential energy of the block 4. Write the Lagrangian function (don't derive the Euler Lagrange equa tions) reference plane
* F2 # 3 E Problem 4. EOM Derivation Derive the equation of motion for the following system: We want to measure the spin rate w of the rotating shaft of a turbine. To do it we push a small mass m against the end of the shaft. The shaft makes friction contact with the drag cup mounted on the mass. The frictional torque is b (w). Assume that the rotational spring torque is ke and that the moment of inertia of mass m is J. J Rotating Shaft F3 @ $ 4 R b J, m Drag Cup F4 Q Search % 5 F5 T 0 Wall * A 6 F6 Y 2 * F7 & 7 PrtScn U F8 4 8 Home 6. F9 9 End F10 Po 0
A simple single degree of freedom model of a wheel mounted of a spring as shown in figure below .the friction in the system is such that the wheel rolls without slipping. Calculate the natural frequency of oscillation using the energy method .Assume that no energy is lost during the contact x(t) k m,J The rotation of the wheel (of radius r) is given by 0(t) and the linear displacement is denoted by x(t). The wheel has mass ( m) and moment of inertia (J) ,and the spring has stiffness (k ).
For each configuration shown in Figure 2, find an expression for the angular frequency andorder them from largest to smallest. Assume that all the springs shown have the same spring constant.spring k and all blocks have the same mass m.
In the system in the figure, the static equilibrium position of the thin, slender homogeneous rod of mass m and length L is horizontal.During the movement of the system, the bar is separated from the horizontal by small angles. (A makes oscillating motion with small angles relative to the simple support point)a) Find the equation of motion of the system in terms of the given parameters.b) Since M=4 kg, m=1 kg, L=1 m, k=600 N/m, c=200 Ns/m, F=300 N, w=4 rad/s, is there resonance in the system? If there is resonance, what would you recommend to get rid of resonance?
Figure Q9 shows part of a system with many degrees of freedom. Write the equation of motion for m₂. Specify the assumptions that you may need to consider in determining the relative displacements and subsequent spring forces. ■ ■ ■ Kn-1 i M Fn-1 Kn Juny mn-1 mn kn+1 Fn mn+1 Kn+2 n
3. Imagine a door which can swings into and out of a room. The door has a closer with a spring stiffness of 71 N-m/rad and damping of 7.5 N-m-s/rad and mass moment of inertia of the door with respect to the hinge is 20 kg-m?. If the door is held open and then let go from an angle of 50 degrees, how long will the door continue to swing into and out of the room? How many times will it swings before it will closed? Assume that the door is considered closed when the amplitude has decreased to 2.5 degrees. Assume that small angle approximation holds, such that sin(theta) = theta. %3D
A uniform rod of mass m is pivoted at a point O as shown in Figure 2. The rod is constrained by three identical linear springs, and a point mass M is attached at the end of the rod (also shown in Figure 2). The parameters of the system are as follows: L= 1 m, k = 1000 N/m, m= 50 kg, M = 25 kg. i. Derive the equation of motion of the system in terms of the angular displacement (0). Choose O as the clockwise angular displacement of the rod from the system's static equilibrium position.
Q1: The system shown has two masses. Beam of mass (Jo#m L² kg.m²) rotates about fixed point (O) and its free end is connected to disk rotates about fixed point (O₂). Consider all connecting links are massless and rigid. Find 1- The displacements of points A, B, and C in addition to the rotations of masses, all in terms of 0. 2- Find the equation of motion (EOM) in terms of 0. 3- What is the natural frequency of the system? 0 L/2 8 Energy methods A Jo=m L²2 L/2 Joz-m R² R C B C 128
Rotor Hub Low-speed shaft Gearbox J1 ktl - High-speed shaft k,2 Nacelle 02 Tower -Generator J2 Figure Q2 Blade Blade
Q3) A 16 Ib cylinder stretches a spring 2/27 inches by itself. The spring is initially displaced 1/2 ft upwards from its equilibrium position and given an initial velocity of 12 inches/sec downward. Find the displacement at any time. The damping force on the system is 6 times the instantaneous velocity.
Problem 5 Consider the two-mass system connected by two springs. Let coordinates x, and x, be such that when they are both zero, the springs are at their natural lengths. Write down the equations of motion. Use the Matlab command ode45 to solve the initial value problem with parameters m = m2 = k, = 1, k2 = 10 and initial conditions x,(t = 0) = *,(t = 0) = *,(t = 0) = 0, x2(t = 0) = 0.1 for te [0,67]. Plot x, and x2 as functions of t. Submit your plot as well as codes.