fluid mechanics Refer to Figure 2 and determine the requiredforce at C for the gate to be in equilibrium.SG -0.7280 cmHinge10 cmWidth of theSG-1.30150cmgate is 3.5mB.Note: Dark horizontal andvertical lines act as one gate.S0 cmFig. 2

Solution:- Given, SG=0.72/80cm SG=1.30/150cm Width=3.5 cm

Answered: Refer to Figure 2 and determine the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Im 3m 3 m SOLVE FOR ALL THE FOCES IN Im EACH MEMBER RADIUS OF PULLEY = 0. Tm %3D 2m 700 KN
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
SOLVE STEP BY STEP IN DIGITAL FORMAT Determine by the method of nodes the forces at which the members EG, GF and FH, EF and ED of the following truss work. 4 kN 8 kN 2 m G 2m H. 8 kN 2m E 2m 8 kN 2m 2m 4 kN 2m 2m A B.
The rope ABexerts a 46 - N force T on the collar at A Let rCA be the position vector from point C to point A. (Figure 1) Figure K 1 of 1 > 0.15 m 0.4 m 0.2 m 03m 05 m 0.25 m 0.2 m
The length of the 2 mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 2 mm exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=200GPA, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D 0.3 m | 20 kg 2 mm 0.3 m 0.1 m
Determine the member force CD(kN) in the figure shown. 50 AN 50 N S0 AN
Jertical beam of the applied to a shown. Determine forces are cross section compressive BC of the the maximum Stresses bRam. tensile and portion. 9,25 kN in 45mm I10mm 30 mm 30mm 400mm 500mm
Analyze the given frame. P units in kN/m P 3m P 5m 4m pin 0.7P 4m
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis
Compute the forces in hars AB, AC, DF and DE in the scissors truss shown below: 12 Kips F 12 Kips B D 12 Kips 10 C (T/ H 12 kips G 12 Kips H 48 10²✨ 10² … 10¹. 10² × 10² J th
QUESTION 1 THREE PINNED STRUCTURE The structure shown in Figure 1 below represents an elevation of a typical frame which is supported at nodes A and B as indicated. The frame is subjected to forces as indicated and has a hinge at D. Joint C is a rigid joint. Note: 120kN is perpendicular to member BD. 1.5m 5m 35 kN/m LU/NOR ▬▬▬▬▬▬▬▬▬ Elgure 1 1.5m 120 KN 45° M 1.5m 4 Draw a neat, fully annotated shear force and bending moment diagram, including the maximum in span moment where appropriate. S E

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Refer to Figure 2 and determine the required force at C for the gate to be in equilibrium. 450 SG-0.72 80 cm Hinge 10 cm Width of the gate is 3.5m SG-130 150cm Note: Dark horizontal vertical lines act as on 50 cm Fig. 2