Please help with these questions. Read the setting on this metric vernier micrometer scale graduated in 0.002 mm.-353025°510 1520 Read the setting on this customary vernier micrometer scale graduated in 0.0001".10-50120

Absolutely! To read a vernier micrometer:Summary:The reading on the micrometer is approximately…

Answered: Read the setting on this metric vernier…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Determine the reading on the vernier scale as indicated by the arrows. OMARKS 5 3 4 5 6 7 8 9 10 Reading.. .mm Page 6 of 7 LO
Read the setting on this customary vernier micrometer scale graduated in 0.0001".
Show the tolerance zone created by each of the given tolerance specfication. Superimpose the tolerance zone on the given drawing.
For measuring a wire of thickness 1mm , out of a ruler, vernier calipers and Micrometer which one will be more accurate and which one will be less accurate? If the main scale of vernier calipers has calibrations, 1cm divided in two 20 divisions and the vernier scale has 10 divisions on it, what is its least count? 7. Write the correct reading of the micrometer screw gauge given in the figure. mpie 3" mark below 0 10 zero error = Correct reading = ||
2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50 Reading.. .mm 3. Determine the reading at the points shown on the steel rule: A D 1/8 1/4 12 21 A. = B. = C. = D. = Page 6 c
Suppose that the length of the steel bar is measured by a number of different observers and following set of 11 measurements is recorded as set A (units mm): 398, 420, 394, 416, 404, 408, 400, 420, 396, 413, 330. Next the measurements are taken using different ruler to produce measurement set B: 409, 406, 402, 407, 405, 404, 407, 404, 407, 407, 408. It can be shown that the mean values set A and B are 409 and 406 respectively. Which of the two measurement sets A and B, and the corresponding mean value, should have most confidence in? why? Text
On the toleranced rectangle below, state the tolerance within which the top surface must be flat. 1.000 1.010 1.010 1.000 There is no tolerance within which the top surface must be flat O .010
The tolerance for a ball bearing is 0.01. if the true diameter of the bearing is be 2.0 inches and the measured value of the diameter is x inches, express the tolerance using absolute value notation.
6. Comment on accuracy and precision of the spherical ball diameter measurements at Instruction 2 2. Measure the diameter of spherical ball five times with micrometer Then, fil the table with your results. No. Micrometer (mm) 1st 8.01 2nd 8.00 3rd 8.00 7 99 7 08 4th 5th
draw the isometric and pictorial figure of the given measurement below
Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your answer should have 0 decimal places needed. Ex: 76,440 10 - 30 B
0.5mlm 1 3 4 5 cm mm} Consider the steel ruler shown. Which of the following dimensions can be accurately measured with this ruler? C. 1.05 mm B. 1.5 mm A. 1.25 mm D. All of these dimensions can be measured accurately

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Read the setting on this metric vernier micrometer scale graduated in 0.002 mm. -35 30 25 ° 5 10 15 20 Read the setting on this customary vernier micrometer scale graduated in 0.0001". 10 -5 012 0