Read the setting on this customary micrometer scale graduated in 0.001".

Q: On the toleranced rectangle below, what is the tolerance within which the to be parallel to the…

A: Parallel symbol describes a parallel orientation of one reference feature to a datum surface or the…

Q: Shown here are some dimensions along different architect’s scales. Locate the zero point on each…

A: To measure a length to scale: First, find the edge of the ruler containing the scale - in this…

Q: Enumerate the remaining measurement quantity and Unit

A: Time-si unit second, length-si unit meter, mass-si unit kilogram, electric current-si unit…

Q: If the main scale reading(mm) and vernier scale reading (division) are 11 and 15 respectively for a…

A: main scale reading = (MSR) = 11 mm vernier scale reading (VSR) = 15 mm no of division = 20

Q: If the main scale reading (mm) and vernier scale reading (division) are 28 and 18 respectively for a…

A: We have to find measurement of vernier caliper

Q: If the main scale reading (mm) and vernier scale reading (division) are 49 and 10 respectively for a…

A:

Q: Q- In a limit System, the following limits are Specified for hole and shaft. calculate the tolerance…

A: The limits of the hole are..The limits of the shaft are..

Q: 28. Two identical cubes which are machined to 1.000 +/- 0.005 inch, are glued together. Glue…

A:

Q: 0.5mlm 1 3 4 5 cm mm Consider the steel ruler shown. Which of the following dimensions can be…

A: The least count of the ruler is 0.5mm, therefore, the ruler can only accurately measure measurement…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: Determine the relative roughness of cast iron pipe with inner diameter 3.1 inches. Your answer…

A: Given Internal Diameter (D) = 3.1 inches                                    = 3.1 * 25.4 mm…

Q: Calculate to the correct number of significant figures. 1.54 x 0.03060 x 0.69

A: The number of significant figures in the number 1.54 is 3 as all digits are non-zero. The number of…

Q: A slip gauge setting height  of 65.215mm is observed and an angle of  480 is found during the…

A: Given data, Slip gauge height  (h) = 65.215 mm Angle (€) = 48° Find  Length of sine bar (L)

Q: A slip gauge setting height 53.155 mm is observed when a sine bar of the length 127 mm is used…

A: Angle using sine bar and slip gauge is find out by Angle = Sin-1(slip gauge height/ length of sine…

Q: Compute Îx (I bar sub x, in inches“, round-off to 2 decimal places) for the region shown. 6 in. 6…

A:

Q: Determine the forces in members BC and CF of the loaded truss. Enter a positive number if in…

A:

Q: ZPQ'R= = LPQ'R= = MI i O rad

A:

Q: f the metric micrometer to a precision

A: 5.332

Q: Show a scale diagram indicating a reading of 0.206 inch in a micrometer.

A: Given question : Show a scale diagram indicating a reading of 0.206 inch in a micrometer.   The…

Q: 37. Show the tolerance zone for the given slot. Superimpose the tolerance zone on the given drawing.…

A: Given, The tolerance for the offset is T=±0.02 units So, the thickness of the tolerance zone is…

Q: High precision in angular measurements can be made using a sine bar. For using a 300 mm sine bar to…

A:

Q: 1st image : What is the reading on the micrometer? 2nd image : What is the reading on the…

A:

Q: The least count of  a  micrometer is a. 0.01 mm b. 0.2 mm c. 0.05mm d. 0.1mm

A: Option a is correct.

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: The height (in mm) for a 125 mm sine bar to measure a taper of 27'32' on a flat work piece (correct…

A: Given:Length of sin bar, L=125 mmθ=27o 32'θ=27+3260oθ=27.533o

Q: Use prefix multipliers to express each measurement without any exponents. 87.9 x 10-L

A: Given: The expression is 87.9×10-7 The scientific notification for the expression is, 87.9×10-7…

Q: Read the metric caliper in millimeters. Take note that the numbers marked on the main scale are in…

A: The given scale is simple vernier caliper reading. Whose least count is given LC= 0.05 mm  And the…

Q: igh precision in angular measurements can be made using a sine bar. For using a 200 mm sine bar to…

A: Given:Length of sine bar, L=200 mmangle=49o 20'angle=49+2060=49.33oDiameter of rolls, d=35 mm

Q: C. Read the measurements on the following micrometers:

A: Given Pictorial representation of a micrometer  To Find the reading of the micrometer

Q: Read the following millimetric vemier caliper setting 5. 5 6 78 0.05mm A BI

A: It is required to determine the reading on Venturi meter

Q: A slip gauge setting height 50.14 mm is observed when a sine bar of the length 147.32 mm is used…

A: Slip gauge angle

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Show the tolerance zone created by each of the given tolerance specifications. Superimpose the…

A: We have to show the tolerance zone created by each of the given tolerance specification. And,…

Q: Read the micrometer. 10 5 0. 2 تأسست 3 بليل 4 5 -5 0 -20 The length shown on the micrometer is (Type…

A: Given: To find: Micrometer reading=?

Q: Thermal efficiency of a power cycle is 0.8. For the cycle, Qout = 250 kJ. Determine Qin in kJ.

A: Answer: Oin = 1250 kJ.

Q: Comment on accuracy and precision of the spherical ball diameter

A:

Q: A slip gauge setting height of 63.205mm is observed and an angle of 40° is found during the precise…

A:

Q: The micrometre is a direct measurement device with a least count of 0.01 mm, that has 20 divisions…

A:

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: If the difference in the taped distance and paced distance is 0.90 m and the tape distance is…

A: The relative precision of a measurement is defined as the ratio of the discrepancy in value to the…

Q: 6. On an engineering drawing a dimension is laid out as 1.760 ± 0.005 A note on the drawing states…

A: (a) The nominal dimension = 1.760 inches. (b) The upper limit = 1.765 inches. (c) The tolerance = ±…

Q: A B D (a) If the gap, w, must be at least 0.015 in for the proper functioning of the assembly, what…

A:

Q: Tolerance Table All dimensions in inches 11.0 + 0.4 3.1 X.X +0.1 15.00 + 0.25 3.100 Х.XX +0.05…

A: