ratio of connecting rod length to crank radius.

Q: Describe the product of inertia for an area?

A: Product of inertia for an area is defined corresponding to two rectangular axes, the summation of…

Q: Swivel flange center helps to permits the rod buckling due to compression or tensile shock forces.…

A: Answer: True The given statement Swivel flange center helps to permits the rod buckling due to…

Q: Hi guys.  I need some advice in this problem. Can u please help me?

A:

Q: Outer Bearing Nut Lock Inner Bearing Thrust Washer Spindle Oil Seal 01100 Hub Сaр Cotter Pin Nut…

A: tapered wheel  as Follows

Q: Can I get some help looking over some sheets? I have most filled out, but just to double check for…

A: During four stroke the crankshaft turns twice — moving each piston up and down twice — while the…

Q: Swivel flange center helps to permits the rod buckling due to compression or tensile shock forces.…

A: Gievn that    Swivel flange center helps to permits the rod buckling due to compression or tensile…

Q: if there is an angular decoupling between the shaft and the hole, which Bearing type is preferred…

A: Option A - that is roller bearing type is used for this kind of arrangement. Roller bearing hold…

Q: 8-5 lem 8-5 The machine shown in the figure can be used for a tension test but not for a compression…

A:

Q: -) Draw free hand and proportionate sketches for any four of the 1- Pan and rounded countersunk head…

A: Rivets are used for the fixing of two or more objects. Different types of rivets used in engineering…

Q: The thread depth is  measured along the ----------------- of the thread. Pitch Crest Angles Face

A: Thread: A thread is a simple machine structure mainly used to convert the the linear motion of force…

Q: I need the answers to this question.

A: The explanation of the above terms have been explained below.

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an…

A: Diagram 1. E - relief valve A- gear pump D- rotor F- internal gear C- internal and external gear…

Q: Universal joint is used for non parallel shafts whose axes are O coplanar. connecting radiator…

A: Universal joint: The universal joint is a joint between two rotating shafts which allows to move the…

Q: identify the tapered and drive axle bearing parts in the drawing. Place the identifying letter nexe…

A: Tapered roller bearings contain tapered inner and outer ring raceways with tapered rollers…

Q: In the mechanism shown, where h = 9.0 cm, R = 22.6 cm, q = 35.0 cm and no offset, determine, Minimum…

A: 1. For withworth quick return ratio,  the ratio of time of forward stroke to the the return stroke…

Q: In SRP the main function of crank shaft is to convert rotary motion to reciprocating motion. Select…

A: Correct Option: True.

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: is the wheel provided with a series of backward curved vanes. Select one: O a. Spiral casing O b.…

A: The centrifugal pumps are made up of many components like the suction pipe, delivery pipe, casing,…

Q: When it comes to finding the moment arm, you must use the distance of the line from the pivot to the…

A: Explanation When it comes to finding the moment arm, you must use the distance of the line from the…

Q: A significant disadvantage of using a flywheel with a reduced moment of inertia would most likely…

A: Given:   To select the correct option for the disadvantage of using a flywheel with less moment of…

Q: How many primary joints are there in this mechanism? 22.9 22.9 /D E 4.5 typ.

A: Primary Joints include pins, sliders and other elements that allow pure rotation or pure linear…

Q: An engine makes 259HP at redline, and 280 ft-lbs of torque at 4500 RPM. Th 4cylinder Boxer engine…

A: As per the guidelines, I can solve only first question, for second question, please repost in a…

Q: The transformation from the last joint to the tool contains a rotation of 90 degrees. Select one:…

A: That is true, as we know that the transformation from the last joint to the tool contains a rotation…

Q: ___________mm4 is the polar moment of inertia of a hollow shaft if its external diameter is 150mm…

A: The polar moment of inertia is termed as an axis which is basically perpendicular to the plane of an…

Q: Instructions: Identify the tapered and drive axle bearing parts in the drawing. Place the…

A: Tapered roller bearings contain tapered inner and outer ring raceways with tapered rollers…

Q: engine is square with bore equals to stroke. Determine the following a. Cylinder bore and stroke b.…

A: To find-: (a) The cylinder bore and stroke. (b) The average piston speed. (c) The clearance volume…

Q: What is the power (?) lost to main crankshaft friction in a four-cylinder engine with a 100mmbore…

A: Solution: Given Data: n=4D=100 mms=100 mmN=1500 rpmBn=5dn=50 mmln=25 mm   To Find: Power lost to…

Q: When facing, the compound rest maybe set 30° (to the cross-slide. If the compound rest is fed in…

A: Draw the diagram of the cross-slide and compound rest.

Q: In the drawing, arm A is being driven back and forth in the direction of the arrows. It is connected…

A: Solution: Given Data: Screw B is lowered towards the end of arm A.   To Find: What happens to the…

Q: 5-The flame termination is ending at 20 degree aTD for 4-stroke Cl engine with 6-cylinders with…

A:

Q: The rolls are supported on bearings of side frames called *

A: The rolls are supported on bearings of side frames called Answer: Supports

Q: cylinder failed due to static load or cyclic load

A: The failure occurs in wheel cylinder due to cyclic loading.

Q: QUESTION 2 The equation of the turning moment dagram for the three crank ençines is given by: T(0) -…

A:

Q: Determine the cylinder displacement and engine displacement of an engine having six cylinders with a…

A: Number of cylinders = 6  Bore = 400 mm  Stroke = 160 mm

Q: The straight surface on either side of the screw thread is known as Flank Root Crest Pitch

A:

Q: Part of the screw thread connecting the adjacent flank on the bottom of the screw thread is known as…

A: Crest - In the top portion, it joins the sides of the thread. Root - in the bottom portion it joins…

Q: 10. The design life of a bearing used in a shaft of an industrial blower is around 20,000 h. How…

A: Given : Lₕ = 20000 hours N = 600 rpm     The expression for life of bearing in million revolutions…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.