R-4.3 A cantilever beam is loaded as shown in the figure. The bending moment at 0.5 m from the sup- port is approximately: (A) 12.7 kN m (B) 14.2 kN m (C) 16.1 kN m (D) 18.5 kN m 456 A 4.5 kN 1.8 kN/m -1.0m- -1.0 m-1.0 m-3.0 m- B

R-4.3 A cantilever beam is loaded as shown in the figure. The bending moment at 0.5 m from the sup- port is approximately: (A) 12.7 kN m (B) 14.2 kN m (C) 16.1 kN m (D) 18.5 kN m 456 A 4.5 kN 1.8 kN/m -1.0m- -1.0 m-1.0 m-3.0 m- B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

F=20 kN single load, M=21 kN.m moment and w=20 kN/m distributed load act on the beam whose loading condition is given in the figure. The length L is given as L=6 m. The cross-sectional characteristics of the beam are body height yg= 170 mm, body thickness xg=10 mm, flange width x+=120 mm, flange height yf=10 mm. The Enocta on the beam section is located just below the flange-body junction. According to this;a) Find the support response in the y direction at point A. (Write your result in kN)b) Find the support response in the y direction at point D. (Write your result in kN).c) Find the shear force at point B. (Write your result in kN)d) Find the bending moment at point B. (Write your result in kN).e) Find the normal stress due to the bending moment at point E in the section taken from the B line of the beam. (Write your result in MPa).f) Find the shear stress due to the shear force at point E in the section taken from the B line of the beam. (Write your result in MPa).
Ql: A beam with overhang is supported and loaded as shown in Figure. Draw the shear force and the bending moment diagrams, showing clearly the position and maximum B.M in the beam. 20 KN stma 4 m 3m
F=20 kN single load, M=30 kN.m moment and w=10 kN/m distributed load are acting on the beam whose loading condition is given in the figure. The length L is given as L=3 m. The cross-sectional characteristics of the beam are body height yg=200 mm, body thickness xg=15 mm, flange width xf=150 mm, flange height yf=15 mm. Point E on the beam section is located just below the flange-body junction. According to this; a) Find the support response in the y direction at point A. (Write your result in kN) Answer b) Find the support response in the y direction at point D. (Write your result in kN). Responsec) Find the shear force at point B. (Write your result in kN) Answer d) Find the bending moment at point B. (Write your result in kN). Response e) Find the normal stress due to the bending moment at point E in the section taken from the B line of the beam. (Write your result in MPa). Response f) Find the shear stress due to the shear force at point E in the section taken from the B line of the…
A beam of 8 m long, loaded with uniformly distributed load on the 4 m span CE with a concentrated load on C and moment on B as shown in Figure. Draw the Shear Force and Bending Moment diagrams stating the important values..Note: SN = %3D Student Number SN (kN) SN (kN/m) SN (kN.m) A E B C D 2 m 2 m 2 m 2 m
Plot the bending moment diagram
The cantilever beam AC shown in the figure is subjected to a load 1kN at the end A, and an in- plane clockwise moment 5 kNm at B. The shear force and bending moment in the beam at C are respectively, 1 kN 2 m 3 m O a. (-)1 kN, 0 Ob. 1 kN, 5 kNm OC. 1 kN, (-)5 kNm Od. (-)1 kN, 10 kNm
H.W: Find the values f the shear stress at point A, B, and C in the beam Cross-Sedion shown in the figure below when subjeded to a shaur forced Q= loo kN. Hence Sketch the shear stress distribution dingram. A R2 25 mm R= 50 mm R= 75 mm
A beam of 8 m long, loaded with uniformly distributed load on the 4 m span CE with a concentrated load on C and moment on B as shown in Figure. Draw the Shear Force and Bending Moment diagrams stating the important values..Note: SN = 41 Please please please need this quickly please please please