Question Two blocks of rubber with a modulus of rigidity G = 12 MPa are bonded to rigid supports and to a plate AB. C = 100 mm and P = 45 kN. B 1. Determine the smallest allowable dimension a of the blocks if the shearing stress in the rubber is not to exceed 1.4 MPa and the deflection of the plane is to at least 3.3 mm. provide answer in mm with precision to two decimal points. 2. Determine the smallest allowable dimension b of the blocks if the shearing stress in the rubber is not to exceed 3.7 MPa and the deflection of the plate is to be at least 5 mm. provide the answer in mm with precision to two decimal points.

Question Two blocks of rubber with a modulus of rigidity G = 12 MPa are bonded to rigid supports and to a plate AB. C = 100 mm and P = 45 kN. B 1. Determine the smallest allowable dimension a of the blocks if the shearing stress in the rubber is not to exceed 1.4 MPa and the deflection of the plane is to at least 3.3 mm. provide answer in mm with precision to two decimal points. 2. Determine the smallest allowable dimension b of the blocks if the shearing stress in the rubber is not to exceed 3.7 MPa and the deflection of the plate is to be at least 5 mm. provide the answer in mm with precision to two decimal points.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Determine the nominal load P that will cause failure of the beam shown below. As part of your solution, include sketches of the distribution of strain, the actual distribution of stress, and the equivalent rectangular stress block distribution of stress when appropriate. Reinforcing bars are 4-#7 bars. Material strengths are f. 5.5 ksi and f, = 60 ksi. You may ignore the beam self- weight for this problem. %3D 24 in.! 3 in. 21 in. C A 16 ft 16 ft
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
Determine the compressive force (in N) in the bars shown after a temperature rise of 165°F if d = 0.011 in. Round off the final answer to five decimal places. d ... L M Use the following data: Bronze Aluminum A = 2.33 sq. in E = 14988461 psi A = 2.6 sq. in E = 10519262 psi L = 17.3 in L = 12.6 in a = 11.71 x 106/ °F. a = 12.73 x 106/°F
In figure shown below B 960 Imm 640 N 3 280 mm 960 N a. Determine the tension in segment AC b. Determine the tensibn in segment BC
Homework 8: A (20°C) a rigid beam in placed upon the rods shown in figure: 1) Determine the magnitude of uniformly distributed load w (kN/m) so that beam remains horizontal when temperature of steel becomes to (100°C). 2) Find the stress developed in each rod. Steel A, = 1000mm², as = 12 * 10-6 , E, = 200GPA, L = 500mm %3D %3D Aluminum Aal 1500mm2, aal = 23 * 10-6 , Eal = 70GPA, L = 300mm %3| Rigid beam w (kN /m) A C steel Aluminum 3m 3m
Assume that the truss is simply supported at joints M and E. Determine the stress at member DE if Pu = 18.375 Kips, the area is 23 in?. Answer your problem with the given unit ksi. Pu Pu Pu Pu Pu Pu Pu * (a: 10' - J I H G K F * (a ' - RI Rv 8@10'=80
1. A stepped cyllindrical bar carries axial forces as shown. What is the maximum value of P for stresses not to exceed 100 MPa in tension and 120 MPa in compression? AAB = 360mm2 ABC = 240mm2 ACE = 300mm2 5P 4P 3P A B C D 3P E חו P
A 31 mm diameter bronze bar 3.7 m long is placed between two rigid walls. At a temperature of -39°C, the gap A = 2.3 mm. Find the temperature(at degree-Celsius) at which the compressive stress in the bar will be 40 MPa. Use a = 19.84 x 106 m/(m-°C) and E = 82 GPa. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
You are an engineering intern at a manufacturer of mechanical tools, your senior engineer asked you to evaluate the stresses on a newly-design utility hook, shown in Figure.6, to confirm it's not exceeding its yield strength. The hook dimensions are (d, D¡, L) = (20, 75, 250) mm. The task can be completed by calculating the stresses at the inner and outer surfaces of section A – A when the load is F = 4 kN. L Figure.6: Utility hook
Define the following:a. Proportional limitb. Elastic limitc. Yield stress
Learning Goal: The member shown is subjected to a compressive stress in the x direction of o₂ = 400 ksi and a compressive stress in the y direction of oy = 700 ksi The dimensions of the member are a = 3.75 in, b = 1.50 in, and t = 0.75 in. Assume that E - 29000 ksi and that Poisson's ratio is v= 0.29.(Figure 1) Figure V o 9 1 of 1 ▼ Part D - Change in dimension of the member The applied stresses cause the member to experience a change in all of its dimensions. What are the new dimensions, d', b', and t', of the member due to the applied stresses? Express your answers in inches to three significant figures separated by commas. ► View Available Hint(s) d', b',t' = Submit == Provide Feedback 175) ΑΣΦ ΠΨΓ 41 vec → 0 in, in, in Next > 10:55 PM