Question O Answered step-by-step A solid transmission shaft is 3.5 inch in diameter. It is desired toreplace it with a hollow shaft of the same material and same torsional strength but its weight should only be half as much as the solid shaft. Find the following a. Outside diameter of the shaft b. Inside diameter of the shaft c. The volume of hollow shaft per foot length d. The shearing stress of hollow shaft if it is used to transmit 150KW at 600 rpm, Mpa

Question O Answered step-by-step A solid transmission shaft is 3.5 inch in diameter. It is desired toreplace it with a hollow shaft of the same material and same torsional strength but its weight should only be half as much as the solid shaft. Find the following a. Outside diameter of the shaft b. Inside diameter of the shaft c. The volume of hollow shaft per foot length d. The shearing stress of hollow shaft if it is used to transmit 150KW at 600 rpm, Mpa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

مقاومة المواد
I am struggling with this question
A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?
The outside diameter of a hollow shaft that is twice its inside diameter .what is the ratio of its torque carrying capacity to that of a solid shaft of the same material and the same outside diameter?
Given a spring with 2.032 mm wire diameter, oil tempered, 8 active coils, OD is 8.5 mm. Determine the free length if the stress will not exceed 820 MPa when spring is compressed solid. Use G = 83 MPa and assume the springs has plain ends. a. 51.6 mm b. 41.6 mm c. 31.6 mm d. 21.6 mm
Consider a hollow circular shaft subjected to a uniformly distributed torque as shown. Which of the following best describes how the angle of twist varies along the longitudinal axis of the shaft? Select one: O A. Quadratic O B. Doesn't Vary (zero) OC. Doesn't Vary (constant and nonzero) OD Linear
The hollow shaft used in the system has the following conditions: Outer Ø:110 mmØ Allowable Shearing Stress:85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
A shaft is 21/2 in. square, and the allowable shearing unit stress for the material is 6000 psi. The torque on the shaft is A. 27,600 in B 20,800 in C. 31,200 in D. 24,100 in
O d. 25T Nm QUESTION 17 A stepped shaft subjected to a uniform torque T along its length is shown in the figure. When D = 2d, the angle of twist per unit length (0/L) of smaller diameter segment is, %3D O a. equal to that of larger diameter segment. Ob. twice that of larger diameter segment. OC.4 times (i.e. 22) that of larger diameter segment. O c. O d. 16 times (i.e. 24) that of larger diameter segment.. QUESTION 18
Question 72 1 pts A hollow steel shaft is stressed to 35 MPa by a torque of 200000NM. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm. O 331.01 O 250.12 O 33.10 O 25.01
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.
Required information A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force FB at the pressure angle shown. Given: FA = 450 lbf, diameter of gear A = 19 in, and diameter of gear B=7.6 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 1.25-in dia. FA Gear A 16 in 20⁰° 14 in Gear B 9 in FB 20⁰ Find the bearing reaction forces, assuming the bearings act as simple supports. The magnitude of the bearing reaction force Rcy is The magnitude of the bearing reaction force Roy is The magnitude of the bearing reaction force Rcz is Ibf. lbf. Ibf.