QUESTION No. 1 A moving particle has a velocity described in the following data: Time (sec) Velocity (m/s) Determine the velocity of the particle at 20 seconds using a quadratic polynomial interpolated at t= 15 sec, 18 sec, 22 sec, using a. Direct Method 0 22 15 24 18 37 22 25 b. Newton Divided Difference Method 24 123 c. Lagrange Interpolation Method

QUESTION No. 1 A moving particle has a velocity described in the following data: Time (sec) Velocity (m/s) Determine the velocity of the particle at 20 seconds using a quadratic polynomial interpolated at t= 15 sec, 18 sec, 22 sec, using a. Direct Method 0 22 15 24 18 37 22 25 b. Newton Divided Difference Method 24 123 c. Lagrange Interpolation Method

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

See example below. Change data but solve method of 11.
600mm 100mm 50mm x 50mm hole 500mm 10mm A 100mm Figure 3 Show that the horizontal neutral axis is 77.56mm below B. Hence, show that the moment of inertia around this horizontal neutral axis is 3178942345mm4. Show the division of your area on a sketch on your answer sheet. a) (use the answers in (a) for (b), (c), (d) and (e)) b) Draw the 3D normal stress distribution of the section subjected to M = -10 kN.m. Draw the shear stress distribution of the section if the section is subjected to a shear force of 10KN. c) d) What part of the shear force is carried by the flange? e) What part of the bending moment is carried by the flange
Solve the ff. Using DOUBLE INTEGRATION METHOD Pls answer ASAP. I'll rate, thanks!
Conductthe following using Double Integration Method. Let El be constant. Given that from Point A, x = 3.16 m. What is the value of El(y)? Given that from Point A, x= 8.43 m. What is the value of Ellv')? Given that from Point A, x = 6.41 m. What is the value of Ely)? Given that from Point A, x = 5.70 m. What is the value of Elv')? 73 KN 38 KN/m 46 KN/m 4.0 m A 6.0 m 1.0 m B
Run the Bellman-Ford algorithm on the directed graph of the following graph (Figure 24.4), using vertex z as the source. In each pass, relax edges in the same order as in the figure, and show the d and T values after each pass. 5 00 -2 00 6. S 8 7 00
Instructions: Solve the following problems completely using Double Integration Method, Area moment method and Conjugate beam method for each problem. Round off your answers to 3 decimal places. w A L Problem 2 10 kN/m a. Location of Amax from A b. Amax A 10 m
Find the relative error of the following cases. Also, detemine the number of significant digits in the approximations a. x = 2.818238112 and x = 2.81823 b. z = 0.00000067 and z = .000006
A1 PLEASE TRY SOLVING. IT IS A erroneous PROBLEM
10 15 Let/be the function whose graph is shown. Select each of the following intervals, it any. on which/ is continuous O(5, 15] O (5, 15) (10. 15) O (5, 10] O (5, 10) O (10, 15] Tartbool
1. Is there a difference between calculated and observed values for the resultant? What could possibly have contributed to this difference? 2. Using the component method, determine the resultant of the following vectors: A 250N 37° S of W В 150N due N C 300N 60° N of E || D = 200N 53° N of W E = 100N 30° S of E
Investigate the following beam in the right. Determine ONLY the value of q; given the following baseline data of the beam. Show your solutions. Don’t forget the unit.
A line's length has been measured repeatedly on different occasions. The following are the results obtained: a. determine the weighted mean of the 5 sets of measurement b. What is the relative precision if the true length of the line is 352.39?