Question: A shunt-connected DC motor operates at its rated terminal voltage. Its no-load speed is 200 radian/second. At its rated torque of 500 Nm, its speed is 180 radian/second. The motor is used to directly drive a load whose load torque T₁ depends on its rotational speed wr. Neglecting rotational speed wr (in radian/second), such that TL = 2.78 x Wr. Neglecting rotational losses, the steady -state speed (in radian/second) of the motor, when it drivers this load, is

Question: A shunt-connected DC motor operates at its rated terminal voltage. Its no-load speed is 200 radian/second. At its rated torque of 500 Nm, its speed is 180 radian/second. The motor is used to directly drive a load whose load torque T₁ depends on its rotational speed wr. Neglecting rotational speed wr (in radian/second), such that TL = 2.78 x Wr. Neglecting rotational losses, the steady -state speed (in radian/second) of the motor, when it drivers this load, is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4/B/ What are the principal characteristics of a series DC motor? What are its uses? Core Mc
16 A 4-pole dc series motor has wave connected winding with 600 conductors. When fed from 250 V dc source, the motor drives a load of 5 kW and takes 50 A with a flux per pole of 10 mWb. The torque developed is (Neglect losses).
• Q5/ in a DC motor. List and describe the types of losses that occur
8) A 230 V fed single quadrant chopper has a 40% duty cycle. A separately excited DC motor is controlled by a chopper. Motor has a back emf constant of 0.5 V/rad/s and 2 22 armature resistance. Determine the torque of motor at speed of 1400 rpm 4.7 N-m 15.44 N-m 10.5 N-m 19 N-m
a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 0 j0.22 0 j0.22 0 0.05 V j6.28 NE E1
a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 n j0.22 0 j0.22 0 j6.28 N E1 0.05 0
An 3-phase induction motor(IM) has full load slip = 0.5%. If the rotor circuit resistance is increased so that R2new =2R2old, then the slip at which the motor develops the same full load torque is=.. * ......
In a 3-phase, 6-pole induction motor, The power crossing the air gap of a 60 Hz is 42.6 kW, and the power converted from electrical to mechanical form in the motor is 39.6 kW. If the total mechanical losses are 1000 W, find the load torque of this motor? Select one: O a. Tjoad = 330.4 N.m. O b. Tjoad = 318.6 N.m. O c. Tload = 305.4 N.m. O d. None
In a three-phase switched reluctance motor having six stator poles and four rotor poles, the pole widths for the stator and rotor poles are the same, with φs = φr = 40°. The currents in the phase windings are applied when the inductances are increasing. Draw qualitively the current and torque wave- forms of each phase and the total torque developed by the motor for a square wave current having. (a) 40° width. (b) 30° width. (c) 20° width.
B/ fill in the blanks: The power factor of a squirrel cage induction motor is.... at light load only. 2. The eddy current loss in an AC electric motor is 100 watts at 50 Hz. Its loss at 100 Hz will be... 3- The rotor power output of a 3-phase induction motor is 15 KW and corresponding slip is 4%. The rotor copper loss will be.... 4- The resistance representing mechanical output in the equivalent circuit of an induction motor as seen from the stator is:.....
3.An induction motor has a rotor resistance and reactance at standstill of 0.1 ohm and 3.5 ohm respectively. At standstill the voltage induced to the rotor is 60volts per phase. If the slip is 5%, determine the rotor current
a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 O j0.22 Q jo.22 0 j6.28 N E E1 0.05 0 V b) A 4 poles , 50HZ ,Y-connected three phase induction motor has the per phase equivalent circuit parameters of ( R3= R2= 0.12 , X1 = X2 = 0.6 , Xm =12 ) N and l2 = 20L0". Use exact equivalent circuit to determine the following at rated slip of 0.03 : I. Stator current II. Magnetizing current II. Power factor IV. Developed torque c) What is the physical meaning for each of the following induction motor parameters: R1 ,R2 ,Rc ,X1 ,X2 ,Xm ?