QUESTION 5 Two structural members B and C are bolted to bracket A. Knowing that both members are in tension and that P = 6 kips and Q = 8 kips, determine graphically the magnitude of the resultant force exerted on the bracket. B 25° 50° O 8.03 O 9.43 O 10.56 O 11.17

Q: Determine the nature and magnitude of forces in the members 1,2 and 3 using section method.

A: The free body diagram of the truss is as follows:

Q: Q.1) Draw Free-Body diagrams of each of the three cylinders shown below. Each of the cylinders has a…

A:

Q: 5. In order to raise the lamp post from the position shown, a force F = 200 lb. is applied on the…

A:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: Q.7. Determine the resultant R of the two forces shown as below. y 60° 600 N 400 N

A: As it is not mentioned that which question need to be solved, please find solution of the first…

Q: 3) Determine the horizontal and vertical components of reaction at the pins A A 45° 900 plf B 16.0…

A: According to the question data a beam BC has  udl load of 900lb/ft  we need to find  Reaction at…

Q: Two structural members B and C are bolted to bracket A. Knowing that both members are in tension and…

A: Consider the diagram shown below for the resultant using parallelogram law.

Q: Collars A and B are connected by a 525-mm-long wire and can slide freely on frictionless rods. A…

A:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: Q.1) For the figure shown if the tension in cable AB is 15 kN, and 32.5 m long. Determine (a) the x,…

A: tension in cable AB = 15 kN length of cable AB = 32.5m length of pole AO = 28m angle made at ABO =…

Q: Knowing that P =75 N and Q=195 N, determine graphically the magnitude and direction of their…

A:

Q: . Three members are pin-connected at A and loaded as shown. Determine the force in nembers AB and…

A:

Q: A farmer uses cables and winch pullers B and E to plumb one side of a small barn. If it is known…

A:

Q: Question 4 Two cables are tied together at C and are loaded as shown. Knowing that P =239 N and a =…

A: Consider below FBD for the given question:   Given, P = 239 N α = 60o   From figure, θAC = (180 -…

Q: A cable stretched between the fixed supports A and B is under a tension T of 1.2 kN. Express the…

A:

Q: What are the tensions in each of the 4 cables supporting the lamp, if the lamp weighs 50 lbs and the…

A:

Q: Calculate the magnitude and direction of the RESULTANT REACTION at each support.

A: for solution refer below images.

Q: Q4) 200 cm X B 300 cm 227 cm 125 cm 75 cm Determine the force acting along the axis of each of the…

A: Mass of block, M=500 kg

Q: 1.25 m N 1.25 m 3m 1.5 m E B G 5 kN 0.751 0.75 m X The rigid L-shaped member ABC is supported by a…

A:

Q: 2 m w N/m B 4.8 m 3 m

A: Given: R=1200 N x= 3.6 m   To find: w= ?

Q: 1 m F А 1 m B. E 45° 45° -2 kN 5 kN termine the magnitude of the force (in kN) in member CD. Include…

A: For solution refer below images.

Q: 668 Ib 250 lb 3

A: Given Data⇒

Q: Question 8

A:

Q: 2. Question : For the given three bar support system, determine the internal forces at the point p,…

A: Given: The system is shown below:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: . A barge is pulled by two tugboats. If the resultant of the forces exerted by the tugboats is a…

A:

Q: Determine the forces in each cable if P = 10KN.

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: The co-ordinates of the given points are,

Q: Pravinbhai

A: The objective of the question is to determine the tensions in cables AB and AD. The tension in cable…

Q: The 47-lb square plate shown is supported by three vertical wires. Determine the tension in wire A…

A: Given weight = 47 lb let Ta,Tb,Tc be the tension in the wire a,b,c respectively Free body diagram

Q: QUESTION 2 Two structural members B and C are bolted to bracket A. Knowing that both members are in…

A:

Q: Determine the magnitude of the force supported by the pin at C of the loaded frame.

A:

Q: Using the knot method, determine the force in each bar of the represented truss. Express whether…

A:

Q: 1. From the cable shown, determine the following: a. Tension at point 3. 15m 15m 15m 15m H b.…

A: Given: To find: Tension in cable at point 3, 2, 1

Q: For the load system shown, F₁ = 500 N, F2 = 900 N, 0= 20 deg, and = 25 deg. The magnitude of the…

A:

Q: The rectangular plate of sides 560 mm x 1590 mm is supported by hinges along its side BC and by the…

A: Given data,the rectangular plates of sides = T=540 N

Q: A crane is mounted on one side of the bed of a pickup. For position θ = 40 °, determine the…

A: Given data as per question  θ = 40 Mass = 120 kg Calculations considering FBD of the…

Q: 4. Determine the horizontal force exerted on block E. F = 150 16 6 in BD 11 8 in a B 150 6 in. D E

A:

Q: Activity 3. From a bar subjected by an axial force P, Draw the components of P acting on the…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.