QUESTION 5 An open-loop transfer function for a root locus is given as: 2K (S + 4) S(S+ 2) (S + 8) Use the given transfer function to determine the following: 5.1 The open-loop poles and the zeros G(s)H(s) = Do some of the loci break away? Explain. The centre of asymptotes The asymptotic angles 5.5 The stability of the system 5.2 5.3 5.4

QUESTION 5 An open-loop transfer function for a root locus is given as: 2K (S + 4) S(S+ 2) (S + 8) Use the given transfer function to determine the following: 5.1 The open-loop poles and the zeros G(s)H(s) = Do some of the loci break away? Explain. The centre of asymptotes The asymptotic angles 5.5 The stability of the system 5.2 5.3 5.4

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

The open loop transfer function of a humanoid's arm control system is given as: K G(s) = 2 s(s + 2s + 2) (a) Clearly locate all poles and zeros on a linear graph paper. Provide calculations for the following: asymptote angles, centroid for asymptotes, and departure angle from complex pole. (b) Plot the complete root locus, with the locus on the real axis is clearly shown. Use the scale of 4 cm : 1 unit for both axes and choose the longer side of the graph paper as the real axis.
For the system with open loop transfer function given by R(s) K s(s + 1) (s² + 4s +13) where K is the feedback gain. Sketch the root locus a) How many asymptotes are there for this system's root locus? what are asymptote angles? What is the center of asymptotes? C(s) b) Does the root locus cross the imaginary axis? where and what is the value of K at that point? c) Is there any break away, break in points? What is the approximate values of these points?
Required information Use the following transfer functions to find the steady-state response yss() to the given input function f(t). NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. T(-) Y(s) F(s) s(e) 10 b. = 9 sin 2t s²(s+1) ' The steady-state response for the given function is yss() = | sin(2t + 2.0344).
2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
R(S) K D s+5 Find Open Loop Transfer function XIS s+2 s+3 Y(s)
(1) Consider the system represented by the block diagram. The closed loop transfer function T(s)-Y(s)/R(s) is (a) T(s)-50/(s+55 s+50). (b) T(s)=10/(s+50 s+55) (c) T(s)=10/(s+55 s+10). (d) None of the above. R(s)- 10 + s+5 5 Y(s)
root locus electrical engineering Don't overthink and reject. Complete the solution as per the given transfer function. No need of quadratic equation just simplify for the exact given transfer function.
Homework: Given the following transfer functions, Draw the complete Root Locus for these systēms at {K=0, 0.5, 1, 2, 3}, then find break-in points and K value? K(s +1) s' +3s + 3.25 G(s) =- K G(s) = s(s +2)
The Gilles & Retzbach model of a distillation column, the system model includes the dynamics of a boiler, is driven by the inputs of steam flow and the flow rate of the vapour side stream, and the measurements are the temperature changes at two different locations along the column. The state space model is given by: x = 0 00 -30.3 0.00012 -6.02 0 0 0 -3.77 00 0 -2.80 0 0 Is the system?: a. unstable b. C. not unstable x+ 6.15 0 0 0 0 3.04 0 0.052 not asymptotically stable d. asymptotically stable -1 u y = 0 0 0 0 -7.3 0 0 -25.0 X
Part A: Find the steady-state solution of the mechanical system shown below: k mu E m G(s) F(t) F(t) = F sin wt Part B: Sketch the root locus for the transfer function: Ks (s+ 4) (s + 3)(s + 1)
Match the transfer function with correct Bode phase plots. G(s) = 5 $+7 G(s)=s+5 G(s) = s+10 S S G(s) = S+ 10 QUESTION 10 90 deg 00 0 deg -90 deg 180 deg B. D 90 deg @ 0 deg -90 deg 180 deg 90 deg @ 0 deg -90 deg 180 deg 90 deg @ 0 deg -90 deg 180 deg
Homework Consider the following transfer functions. Determine 1. Whether the transfer function is proper or improper 2. Poles of the system 3. zeros of the system 4. Order of the system a) b) (s +3)² s(s² +10) S G(s) = G(s) = (s+ 1)(s + 2)(s +3)