Question 5 a) Analyse the beam below and draw the shear force and bending moment diagrams. Use the conjugate-beam method to determine the slopes at the ends A and D and the deflections at points B and C of the beam shown in Fig. 1. 3m 180kN B 270kN с 3m 21 E = 200GPa 4 1 =400(10°) mm² 3m Figure b) Use the conjugate-beam method to determine the slopes at the ends A and D c) Use the conjugate-beam method to determine the deflections at points B and C

Question 5 a) Analyse the beam below and draw the shear force and bending moment diagrams. Use the conjugate-beam method to determine the slopes at the ends A and D and the deflections at points B and C of the beam shown in Fig. 1. 3m 180kN B 270kN с 3m 21 E = 200GPa 4 1 =400(10°) mm² 3m Figure b) Use the conjugate-beam method to determine the slopes at the ends A and D c) Use the conjugate-beam method to determine the deflections at points B and C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q-1: Use double integration method to find the deflection at the pin C and the slope at roller support D for beam shown in Fig. 1. (constant EI) 60KN Fig.1 B 3m 3m » * 3m
2-Determine the slope and deflection at point B of the beam shown by the direct integration method 1(Ut ñş) 50KN m A В 4 m El = constant E 70 GPa %3D I 164 (106) mm4 %3D
Question Two The beam ABC in Fig Q2 is supported on pin and roller supports at points A and C respectively. Determine the slope and deflection at point B of the beam shown by the 1. direct integration method 2. Moment-area method Take E = 70 GPa and I = 335x106 mm4. -2 m- B - 4 m Figure Q2 C 80 kN-m
6. Given the beam loaded as shown, determine the deflection at the midspan. Use Conjugate Beam Method. 270 kN 45 kN/m A C 3 m 3 m- - 3 m El = constant 200 GPa I = 1665x106mm4 E %3D
Determine the maximum deflection of the beam. shown in Fig. 1. Use the conju beam method. Fig.1 60 kN-m A -15 m El = constant E = 70 GPa 1 = 712 (106) mm4 B
4- Determine the vertical and horizontal deflections at joint B of the truss shown using the virtual work method. 3 m m 100 kN -50 kN m EA constant E = 70 GPa A = 1,000 mm²
For the beam shown below in (fig 2), calculate the location of the centroidal axis ?̅, for the cross-sectional area of the T-beam, after that find the moment of inertia I?̀ about the ?̀
3. Determine the deflection at point C for the beam shown by the virtual work method. 3 kN/m A D C 5 m 10 m 5 m I 21 I E = constant = 250 GPa I = 600(106) mm4
Q2: For the beam shown below in (fig 2), calculate the location of the centroidal axis ?̅, forthe cross-sectional area of the T-beam, after that find the moment of inertia I?̀ about the ?̀axis.
In this non-prismatic beamWhen E=60GPa and I= 260x10^6 mm^4By using the AREA MOMENT METHOD find the ff. a) Location and magnitude of maximum deflection b) Rotation at right support in degrees c) Rotation at left support in degrees(PLEASE SHOW COMPLETE SOLUTION)
ASAP
5: Find the deflection at b, c and d for the loaded beam shown in the figure below by using finite difference (EI constant) dx" 9 ΕΙ a 1 1 L/4 2q b L/4 A с L/4 q d L/4 e HTTTT