QUESTION 4 The following code is used as delay in a program: 0104 MOV BX, 0004 0107 MOV CX, FFFF. 010A LOOP 010A 010C DEC BX 010D JNZ 0107 If you modify the code to set BX= 0008: The delay will be increased and program will appear to run faster. O The delay will be decreased and program will appear to run faster. The delay will be increased and program will appear to run slower. The delay will be decreased and program will appear to run slower.

QUESTION 4 The following code is used as delay in a program: 0104 MOV BX, 0004 0107 MOV CX, FFFF. 010A LOOP 010A 010C DEC BX 010D JNZ 0107 If you modify the code to set BX= 0008: The delay will be increased and program will appear to run faster. O The delay will be decreased and program will appear to run faster. The delay will be increased and program will appear to run slower. The delay will be decreased and program will appear to run slower.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Read the Assembly program carefully, understand its working/functionality and answer the below given questions. MOV DX, 0090 MOV DS, DX MOV AX, 0004 MOV DX, AX SUB DX,1Back: MUL DX DEC DX CMP DX, 0 JNE Back MOV [0020], AL INT E INT 7 a. How many times the Loop will repeat?b. What will be value of AL after complete execution of program?c. Write the main idea of the functionality of the program in your own words briefly.
Answer the following Hexadecimal to decimal conversion problem: Convert the HEX NUMBER 8FFE. 99C4 to decimal number ( show steps in paper , scan and submit along with other answers) Decimal number =
2. A 7-segment decoder drives the display shown in figure. If the waveforms are applied as indicated, determine the sequence of digits that appears on the display. BCD/7-seg Ao A Ao 1 b A1 2 A2 A2 4 A3 A3 e b
Problem 3: Please convert the Mealy FSM in Table 1 to a Moore machine by showing the Moore FSM table. Next State, Output Current State Input 0 1 A B,1 D,0 B C,0 B,0 C B,1 A,0 D B,0 C,0 Table 1
What will be the final value of DI after executing the following piece of code? Execute the instructions dependently one after another. CLD MOU CX,OFOH MOU AX,05678H MOU DI,01000H MOU ES, DI SUB DI, DI REPNZ SCASB -R AX-0000 DS-073F 073F:0100 0000 D 1000:0 F 1000:0000 92 00 14 12 54 56 44 78-AD 56 78 FO 00 00 00 00 BX-0000 CX-0000 DX-0000 SP-00FD ES-1000 SS%3073F CS=073F BP-0000 SI=0000 DI=0000 IP-0100 NU UP EI PL NZ NA PO NC ADD IBX SI1,AL DS:0000 CD TUDX.Ux..... .... Notes: 1- Use the DEBUG window to answer this question (values shown are prior to execution and in hexadecimal 2- Write down the final value of DI as four hexadecimal digits without any additional characters.
In HDB3, If the number of non-zero pulses is even, the format used is a. V000 b. B00V c. V00B d. 000V
Q- DA D Find the state graph for the following parallel counter: C B clk clk clk (Handwriting solution is needed: include this in your pdf file) CBA
For the counter shown below,the sequence of counting for this counter is (in decimal): CLK PL U/D Operation Q3 Q2 QI QO PL U/D 1 Load D3 D2 DI DO Counts up Counts down clk 0 111 Select one: O 7-6- 5-4-7.etc 3- 2-1-0-3..etc 7-8- 9-10-11-12-7-8 ...etc Answer is not listed 1-2-3-4-1-2...etc 4-3-2-1-4-3.etc 4-5-6-7-4.etc 7-8- 9-10-11-7, 8, .etc 7-6-5-4-3-7.etc 3-4-5-6-7-3..etc
Solve it fast plz and dont write in the paper plz
For this exercise, create a project using Keil or MCU8051 and use the editor to type a simple code that show the following results: Location Value R1 66H R2 F5H R5 34H 77H 56H 80H 45H Then: Add the numbers in R2 and R5 and save the answer in 51H. Add the current value in A with 'A5H' and save the answer in R6.
Figure 9 shows a 5 bits adder type DAC. If the shift registers s1 and s4 are ON, and the others are OFF, determine the voltage output if the reference voltage, Vref is 10 V. MSB S₁ R 4 $₂ R/2 3 S3 R/4 BITS 2 RAB SA Figure 9 55 R/16 0 LSB R/2 ref
MOV CX, 21 L1: INC DX LOOP L1 How many times will the loop run?