10 ptsQuestion 4What is the electric held strength in units of N/C if the flux through a 2.0m by 1.0m rectangular surface is 817 Nm2/C, if theelectric field is uniform, and if the plane of the surface is at an angle of T/3 radians with respect to the direction of the field? Nodecimal is required and maximum of 5% of error is accepted in your answer.

Answered: Image /qna-images/answer/3b7dfafc-bf0f-46ce-b8d5-8643c900b378.jpg

Question 4 10 pts What is the electric fhield strength in units of N/C if the flux through a 2.0m by 1.0m rectangular suríace is 817 Nm2/C, if the electric held is uniform, and if the plane of the surface is at an angle of n/3 radians with respect to the direction of the neld? No decimal is required and maximum of 5% of error is accepted in your answer.

Question 4 10 pts What is the electric fhield strength in units of N/C if the flux through a 2.0m by 1.0m rectangular suríace is 817 Nm2/C, if the electric held is uniform, and if the plane of the surface is at an angle of n/3 radians with respect to the direction of the neld? No decimal is required and maximum of 5% of error is accepted in your answer.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter15: Experimental Methods

Section: Chapter Questions

Problem 15ETSQ

See similar textbooks

Similar questions

the algebraic sum of the potential rises and drops around a closed loop is zero Current divider KCL KVL Voltage division
solve very very fast in 15 min please
۹:1 ص السبت ۲۷ آذار Lectures 6-7 Ceramics 2020-21.pdf USED SUSOURCE Senior Lecture - Department of Materials Eng. - College of Engineering - University of Qadisiyah EUSOURCE Here Qfr is the energy required for the formation of each Frenkel defect, and N is the total number of lattice sites. (Also, as in previous discussions, k and T represent Boltzmann's constant and the absolute temperature, respectively.) The factor 2 is present in the denominator of the exponential because two defects (a missing cation and an interstitial cation) are associated with each Frenkel defect. Similarly, for Schottky defects, in an AX-type compound, the equilibrium number (Ns) is a function of temperature as N, = N exp Qs ... (2) Where Qs represents the Schottky defect energy of formation. Example 1 Calculate the number of Schottky defects per cubic meter in potassium chloride at 500 °C The energy required to form each Schottky defect is 2.6 eV, while the density for KCI (at 500 °C) is 1.955 g/cm³. Atomic…
The aluminum tube AB of cross section has a fixed support on the base and is supported by a pin at the top of a horizontal beam supporting a load Q = 200 kN. Determine the required thickness t of the tube if its outside diameter for 100 mm and the necessary safety factor in relation to Euler buckling for n = 3.0 (assuming A = 72 GPa). I know the answer, but I cannot understand the critical charge formula. I don't know why to use the constant 2.046 in the formula, can you please show me?
1) A phosphor-bronze spring has the following dimensions: Length of strip = 400 mm Thickness of strip = 0.075 mm Width of strip = 0.5 mm The Young's modulus of phosphor-bronze is 12× 109 kg/m2. Estimate the torque exerted by the spring when it is turned through 90°. %3D [Ans. 0.83 x 10–6 kgm]
The bar ABC in the figure below consists of an AB tube, with an outside diameter of 28 mm and a thickness of 4 mm, connected to a solid bar BC 12 mm in diameter. It is requested to obtain: a) The normal voltage acting on tube AB. b) The normal voltage acting on bar BC.
An Aluminum wire has a length of 200 m and a diameter of 10 mm. Find its resistance of the wire. Select the correct response. O 56.2384 milli-ohm 42.6343 milli-ohm O 72.0654 milli-ohm 32.3253 milli-ohm
L+I]2 ab)" a~bm 1 2. 6 STATICS ENGINEERS MECHANIOCS CHAPTER Lecture Notes: = m- %3D a Z = EXAMPLE: 22 ember Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of the three forces. 4.5 m +3 2.1m Pz 1400 N 900N 1.8m 1000 N 70.6m 1.8 m 1.2m ofT R+b? 14
A cantilever beam model is often used to represent micro-electrical-mechanical systems (MEMS) (see figure). M Cantilever beam Electrode Dielectric substrate Polysilicon anchor The cantilever beam is made of polysilicon (E = 150 GPa) and is subjected to an electrostatic moment M applied at the end of the cantilever beam. If dimensions are b = 1.5 pm, h = 4.3 pm, and L = 300 pm, find expressions for the tip deflection and rotation of the cantilever beam in terms of moment M. (Use available deflection formulas. The beam has constant flexural rigidity EI. Enter the coefficient for M in N-1 for tip deflection and in Num-1 for tip rotation. Enter the magnitudes.) tip deflection M tip rotation M
A poorly designed electronic device has two bolts attached to different parts of the device that almost touch each other in its interior as in the figure. The steel and brass bolts are at different electric potentials, and if they touch, a short circuit will develop, damaging the device. The initial gap between the ends of the bolts is d = 5.0 mm at 27°C. At what temperature will the bolts touch? Assume the distance between the walls of the device is not affected by the temperature change. Steel 0000000 0.010 m 0.030 m Brass 5.0 μm
The steel plate shown below is put in into a rigid chamber, such that spacings of size s-000188 m. To fit the plate, it is heated. It can be assumed that the plate can move frictionless along its edges If x = 4 m and y- 2 m, E - 200 GPa V - 0.28 a = 11.7 x 10 ro When the upper surface of the plate is just about to close with the chamber due temperature increase along y-axis, how much is the stress on its side? Select the correct response 164.063 MPa 54.688 MPa 117.188 MPa
The heater of the automatic defroster in a refrigerator is a resistance wire.The heater uses 110 volts and draws 4.8 amperes of current. Find in ohmsthe resistance.