QUESTION 3: For the following cross section determine: a) Iz and Iy; b) Yield and plastic moments (My and Mp) for bending about z axis only. c) Shape factor for bending about z axis only. d) The moment that causes yielding to extend 30 mm into the section from the top flange and bottom flange into the web (bending about z axis only). Given: Given: E = 200 GPa, Oy = 400 MPa Note that all dimensions in mm.

QUESTION 3: For the following cross section determine: a) Iz and Iy; b) Yield and plastic moments (My and Mp) for bending about z axis only. c) Shape factor for bending about z axis only. d) The moment that causes yielding to extend 30 mm into the section from the top flange and bottom flange into the web (bending about z axis only). Given: Given: E = 200 GPa, Oy = 400 MPa Note that all dimensions in mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please show complete fbd and solutions
DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 237 N F2 = 682 N F3 = 456 N α = 40 degree x = 8 m. Note: for compression, include a negative sign ( - ) and for tension, type your answer as is. Input your answer in two (2) decimal places only.
Hello can you help me with this problem? The value of P is 45Kips
Determine the type and amount of stress in each member of the truss shown below due to wind load using the method of joints. Assume RaH = RbH a.) Solve the stress of all the members b.) Tabulate your answers (length, bar force, type of force)
The rigid frame shown in Figure is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky = 1.0. The beams are W18 x 50, and the columns are W12 x 72. A992 steel is used. The axial compressive dead load is 50 kips, and the axial compressive live load is 150 kips. a. Determine the axial compressive design strength of column AB. Use the stiffness reduction factor if applicable. b. Determine the allowable axial compressive strength of column AB. Use the stiffness reduction factor if applicable.
3. An A36 Steel Cantilever Beam is shown below, also showing its cross section. Determine the following: Given the formula of the Maximum allowable bending stress of steel, fb = 0.66Fy. Where Fy is the Yield Stress of Steel. Where the bending stress for a beam is (fb) = Mc/I, where c is the distance of the centroid to the extreme most fiber of the beam (either top-most or bottom-most distance). Does the Steel fail under the loading given? Use Fy = 450 Mpa. Use the Moment in (a) and the moment of inertia in (c).
For the exact in the figure tensile strength = 8000 N / cm ^ 2 compression safety = 3000 N / cm ^ 2 calculate the largest Mx moment that the section can carry.
Answer the problem question and store value and then use 4 decimal places as final answer then box the final answer. Don’t forget the unit. Take note: Write it on a paper, hand written showing correct answer.
DETERMINE THE FORCE (Ib) IN MEMBER AB OF THE ROOF TRUSS SHOWN GIVEN THE DATA BELOW: F1=61 lb F2- 167 lb 0- 29 degree a 45 degree "Note: for compression, include.a negative sign (-) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. F1 C a D a A
For the following cross section determine: a) Iz and Iy b) Yield and plastic moments (My and Mp) for bending about z axis only c) Shape factor for bending about the z axis only d) The moment that causes yielding to extend 30 mm into the section from the top flange and bottom flange into the web (bending about z axis only) Given:E = 200 GPa, σy = 400 MPa
1 Question 2: 2 The composite beam consists of a wood core and two plates of steel. If the allowable bending 3 stress for the wood is (ae = 20MPA1 for the steel 4 determine the maximum moment that can be applied to the beam. E =11G Pa, E„ = 200G Pa (o = 130MPA 5 6 7 Take: A = B = 80 8 130 mm A mm mm 10 11 M 12 20 mm 13 B mm 14 20 mm 15 16 17 Solution: E 200(1o n = 18 = 18.182 19 E. 1100) 20 The width of steel rpt be increased to an equivalent width for wood: 21 mm 22 23 | =-width (A) = (10) m* 12 24 25 Failure of wood: 26 Mc 27 (O. ma 28 0.5MA 20(10 )= 29 M = kNm 30 31 Failure of steel: nMc 32 (o.) ar 'man 33 (18.182)(0.5 MA) 34 130(10)= M = kNm Ans 35 36 37 38 39 40 41 42 43
DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 214 N %D F2 = 876 N %3D F3 = 435 N a = 38 degree X = 15 m. **Note: for compression, include a negative sign (- ) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. В H A C E G F1 F2 F3