QUESTION 3 A plank L m long is placed in a horizontal position with its ends resting on two inclined planes as shown. The angle of friction is p. Determine how close the load P can be placed near B before slipping impends. L 81 82 X= A 02/ m 40 deg 30 deq 20 deg Answer in three (3) decimal places: m L P 01 B

QUESTION 3 A plank L m long is placed in a horizontal position with its ends resting on two inclined planes as shown. The angle of friction is p. Determine how close the load P can be placed near B before slipping impends. L 81 82 X= A 02/ m 40 deg 30 deq 20 deg Answer in three (3) decimal places: m L P 01 B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
Show complete solution
A cantilever beam shown in Figure B2 is applied with point load of 10KN and pointmoment of 7KNm. By using Macaulay method:Sebuah rasuk terjulur dikenakan beban tumpu 10KN dan moment lentur 7KNmseperti yang ditunjukkan dalam Rajah B2. Dengan menggunakan kaedah Macaulay:i) Derive the moment equation for the beam Terbitkan persamaan momen bagi rasuk
The beam supports the triangular distributed load shown below with Wmax=770 lb/ft. The reactions at A and B are vertical. 6 ft BI D 6 ft C 6 ft W B E 4.5 ft 4.5 ft
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
A vat full of paint (SG = 0.80) is 8 m long and 4 m deep and has a trapezoidal cross section 3 m wide at the bottom and 5 m wide at the top as shown. a. Compute the force on the bottom of the vat. b. Compute the force on the trapezoidal end panel. c. Compute the weight of the paint. Unit of the Correct Answer: kN Decimal Places required in the final answer: 3
Example 1 A rectangular concrete beam 300 mm wide and has an effective depth of 450 mm. What is the design moment capacity of the beam according to the ACI code? Use fe = 27.6 MPa & fy = 413 MPa, Use: 0.003 Pmax = 0.85 x B1 x- fy 0.003 + 0.005 b= 300 mm d =63 mm 2 # 29 d= 450 mm 4 # 32
Ans is - 2.217 Kn
Question 6 What will be the value of P in kN if below structure collapses in a purely sway mechanism? Round your answer to one decimal digit. Plastic moment for all members = 46 kN.m L = 4 m Round your answer to 1 decimal place. Shipping Tool с P→ B A L L D #F L P/₂ E
Please answer only number 1 with complete solution (all computations must be 4 decimal places)
Within few minutes