Please show the solution for the following:Force in the hydraulic cylinder AB = 17142.56Magnitude of the pin reaction at O = 16594.22 QUESTION 3-50"B50"Around off to two (2) decimal placesanswer range: +/- 5 units-6"11"13"The bucket and its load have a combined weight of 4000 lb with center of gravity at G.You may neglect the effect of the weights of the other members. Determine:

Answered: Image /qna-images/answer/2e8a0620-75ed-4d52-8e6a-60e32643c000.jpg

Answered: QUESTION 3 -50" B 50" A ♫ 11" 13" The…

QUESTION 3 -50" B 50" A ♫ 11" 13" The bucket and its load have a combined weight of 4000 lb with center of gravity at G. You may neglect the effect of the weights of the other members. Determine:

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.89P: The steel cylinder with a cylindrical hole is connected to the copper cone. Find the center of...

See similar textbooks

Related questions

Q: a fluid undergoes the fallowing process 1. heated reveresible at a constant pressure of 1.05 bar…

A: Introduction: A thermodynamic cycle is made up of a sequence of thermodynamic events that occur in a…

Q: The engine of an automobile develops 20hp when the automotive is traveling at 50 km/hr. What is the…

A: Write the given data. P1=20 hpv1=50 km/hv2=25 km/h

Q: The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21…

Q: The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal…

Q: Which of the following memory circuits is used tostore trouble codes and other temporary…

A: A type of memory called ROM (Read-only Memory) is utilised to store data permanently. Read-only and…

Q: Laboratory tests on a centrifugal pump, which is directly coupled to a motor running at constant…

Q: What is the smallest V-groove angle that can be weldedusing the FCA welding process?

A: Given Data : Smallest V-groove angle FCA welding process

Q: Determine the following questions. 1. E = 12 V - 12 2. E = 3. E = 100 V 4. E = 50 V 5. E=0103 6. E =…

Q: Q. 6: A steel rod 20 mm in diameter, 400 mm long is co-axially enclosed in brass tube of 25 mm…

Q: One way to prevent leaking from glove valves in a Halocarbon refrigeration system is to employ…

Q: A 500 N force is acting in AB direction. Replace the force with an equivalent force-couple system at…

Q: Wiring harnesses are typically shielded by plasticconduit. What color is normally used to shield…

A: SRS is the abbreviated form of supplemental restrain system. these are the wiring or connectors are…

Q: A dam with a hydraulic turbine–generator located 40 m below the water surface has a rate of 4600…

A: Given that: Elevation = 40 m Mass flow rate = 4600 kg/s Electric power output = 1400 kW Generator…

Q: 2. An industrial freezer is designed to operate with an internal air temperature of -15°C when the…

Q: Task 1 Considering the figure shown below, find below; determine the resultant couple moment of the…

A: As per the guidelines of BARTLEBY we are subjected to solve only three sub parts at a time. Please…

Q: Which of the following is not part of the starter motorcircuit?a. Batteryb. Starting safety switchc.…

A: given; Which of the following is not part of the starter motor circuit?

Q: 9.59. A 3 in. smooth pipeline 100 ft long carries 100 gpm of crude oil. Calculate the head loss when…

A: Given data: d=3 in=0.25 ftQ=100 gpm=0.2228 ft3/sL=100 ft Need to determine the head loss.

Q: A dam has a semi-circular gate at the bottom that is 4 m in diameter. The dam is 12 m high and…

Q: Given the following duty record, how much life is consumed at each stress level? 60 ksi 49 ksi 10…

Q: The motor M is connected to the speed reducer C by the hollow shaft and coupling. If the motor…

A: Given:Power, P=450 KWspeed, N=920 rpmcico=0.8Allowable shearing stress, ζa=90 MPa

Q: Find the force which produce stress 22 N/mm2 on cross sectional area 2 mm2

Q: Technician A says that most transaxles have a countershaftbetween the main and output shafts.…

A: Main shaft is generally the crank shaft which is attached to the engine directly. And output shaft…

Q: Given: A shaft rotates about a fixed vertical axis at a constant rate of f, as shown below. A…

A: Solution: Given Data: Ω=5 rad/sθ˙=4 rad/sθ¨=-3 rad/s2L=2 mθ=0o

Q: Draw SFD and BMD

Q: Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20-mm…

Q: A spherical pressure vessel 400-mm in diameter has a uniform thickness of 6 mm. The vessel contain…

A: GIVEN DATA- D=400mm t=6mm P=8000KPa Ultimate tensile strength =420MPa We have to find factor of…

Q: What work holding device that is used for face milling and peripheral mill, why so? Subject:…

A: Face milling is a machining process in which the milling cutting is placed perpendicular to the…

Q: As shown on the above figure, the component of F in terms of the unit vectors and scalar is Blank 1…

A: Given:MN=88FN=88SN=47

Q: Q.10. To predict the drag on an aircraft at a flight speed of 150 m/s, where the condition of air is…

Q: The four rigid gears, loaded as shown in the Figure, are attached to a hollow shaft. Compute the…

Q: draw the top view of the obeject b) from the top view, draw downward projection line for each part…

Q: AF 8.5 lb force is applied to the handles of the vise grip (Eigure Figure Part A 0.75 in. 1 in. B…

Q: A gas-turbine power plant operating on the simple Brayton cycle has a pressure ratio of 7. Air…

A: Introduction: In the case of a basic Bryton cycle gas power plant, the working fluid is air. The air…

Q: vehicle is producing a sharp, metallic rappingsound originating in the upper portion of the…

A: As per suggestion of Technician A: If the vehicle is producing sharp, metallic rapping sound from…

Q: Gear A has an angular acceleration of 2t3 rads/s², where t is in seconds. The gear is initially…

Q: A force P = 68 kN is applied at the plate-bolt connection shown. Determine the required diameter in…

Q: To perform a modal analysis for a generic structure it is required to specify at least:

A: To perform a modal analysis for a generic structure it is required to specify at least: Answer:…

Q: 200 r.p.m. with the wing An impeller rotating at dimensions (b₁ = 1.5 in., b₂ = 1.0 in., D, 5 in.,…

Q: A force-couple system is acting on the frame as shown. Use A-50N, B-500N, C-80N, and M= 50N.m. The…

A: (a) 383.0128 N (b) 330 N (c) 505.56 N (d) 40.74 degree (e) 717.86mm (f) 618.3344mm

Q: and P₂ (KN) as shown. Analyze the system of axial bars if the allowable stress requirement and axial…

Q: Compute the value of pressure at depth of 12.16 m from top of water

A: Given:depth, h=12.16 m

Q: After resurfacing a brake drum: Technician A cleansit using hot water and a lint-free cloth. He then…

A: A drum brake is a brake where the shoe press is on the inner surface of the drum. It uses friction…

Q: 30° 30° radius At the instant shown, the roller has velocity and acceleration of 3 m/s downward and…

Q: A four-cylinder, two-stroke 2.4-L diesel engine that operates on an ideal Diesel cycle has a…

A: Given that, for the 4 cylinder , two stroke diesel engine, volume of the cylinder = 2.4 L…

Q: A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the…

Q: The 590-kg uniform I-beam supports the load shown. Determine the reactions at the supports.

Q: What two units are used to show the minimum shearstrength of a spot weld?

A: Resistance welding comes in the form of spot welding. One of the simplest and quickest methods of…

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 750 KPa. If the allowable…

A: Consider a thin cylindrical shell of diameter D, thickness t subjected to internal pressure P. Due…

Q: Technician A says that a cylinder wall with too smootha surface will prevent the piston rings from…

A: Rings won't seat properly and will instead "skate" across the surface if the cylinder walls are…

Q: Q. 4: Determine the nature and magnitude of the forces in member CD, DE and EF (Ref. Fig. 4). 2m 82m…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Please show the solution for the following:

Force in the hydraulic cylinder AB = 17142.56

Magnitude of the pin reaction at O = 16594.22

QUESTION 3
-50"
B
50"
A
round off to two (2) decimal places
answer range: +/- 5 units
-6"
11"
13"
The bucket and its load have a combined weight of 4000 lb with center of gravity at G.
You may neglect the effect of the weights of the other members. Determine:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The hook is used to lift the force of P as shown. The section dimensions of a-a is given: P = 40 kN a = 25 mm b = 30 mm c = 70 mm a. Calculate the distance of the centroid of section a-a from the center of curvature in mm. b. Calculate the distance of the neutral axis of section a-a from the center of curvature in mm.
Solve it step by step with free body diagram always use 3 decimal places
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 360.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.30 MN. pressure vessel W bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. cm x10 X
- Find the centroid for the following composite figure - 2m- 2m- 3m 1m 1.5m 5.0m 6.0m 1.0m 8m-
Show complete solutions and figures The diameters of the two cylinders A and B in the figure shown are 80 mm and 750 mm, respectively. The face of the piston is 1.2 m above the face of the weight platform. The space in between the piston and the weight is filled with oil (s.g.=0.80). If F=75 N, Determine the following: the value of Wrequired to maintain equilibrium. a) 38.6 N b) 86.3 N c) 63.8N d) 83.6 N e) None
Fill in all blanks before submission. Round the answer to the nearest integer The figure shows a rod of length 6 ft and weight 100 lb hinged to the ground at point A. The rod rests on a stone in the shape of a sphere of radius 3ft. The center of the sphere O is located at a distance of 5 ft from point A. The normal reaction N between the sphere and the rod is lb. The horizontal component of the reaction at A is lb while the vertical component of the reaction at A is lb. 6 ft The magnitude of the reaction at A is lb. The angle of the reaction at A is 3 ft 0 5 ft
REACTION FOR POINT A PLEASE
Show the steb by step solution
Q4/ find the center of gravity for figure below. 3 in. 4 in. 10 in.
Fluid Force. A swimming pool is filled with fresh water to a depth of 7 feet measured at the deep end. There is not enough water in the pool to reach the shallow end. Assume that the pool is constucted using right angles, except where the bottom of the pool meets the end walls. Use Ah for the height of a typical strip across the face of the wall. 6. The weight density of water is 62.4 lb/ Your anwers should have units: pounds. 4 ft 18 ft 24 ft Declare your variable(s) here. Show your reasoning below: a) find the force on the typical horizontal strip (red) ? b) write an integral for the total force on the (left) wall of the pool
H.w-4 Find the area of the shapes in the figure and then find the center of gravity? 2 m 1 m 1m 2 im 3 m
FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while solving. lb Question: A spherical balloon containing Oxygen (initially at sea level) has a diameter of 8 in. If the uniform density of air is 0.07498 and that the pressure at sea level is 14.7 psia, determine the new ft³ diameter (inch) of the balloon if it has been brought above sea level by 6000 ft.