Q29Please provide justified answer asap to get a upvote Question 29Given a slope with B =35.5 degrees and the sandy soil has shear strength c = 2 kPa,and o' =34.0 degrees, what is the angle, 0 =? for the most critical planeaccording to Culmann's Method? Unit: Degrees%3DBCWFigure 15.10Finite slope7, = c' + o' tan d'.Unit weight of soil = yAanalysis-Culmann'smethodCS Scanned with CamScanner

Given data, ϕ' = 34 degrees, β = 35.5 degrees Formula for the most critical plane according to the…

Question 29 2 kPa, Given a slope with B =35.5 degrees and the sandy soil has shear strength c = and o' =34.0 degrees, what is the angle, O =? for the most critical plane according to Culmann's Method? Unit: Degrees B C W T, H Figure 15.10 Finite slope 7 = c' + o' tan d' Ünit weight of soil = y A analysis- Culmann's method CS Scanned with CamScanner

Question 29 2 kPa, Given a slope with B =35.5 degrees and the sandy soil has shear strength c = and o' =34.0 degrees, what is the angle, O =? for the most critical plane according to Culmann's Method? Unit: Degrees B C W T, H Figure 15.10 Finite slope 7 = c' + o' tan d' Ünit weight of soil = y A analysis- Culmann's method CS Scanned with CamScanner

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter13: Slope Stability

Section: Chapter Questions

Problem 13.13P

See similar textbooks

Similar questions

For the soil profile described in attachment, estimate anaverage peak soil friction angle. Use Eq. (3.31b) attached
control Sharpie.) Pen. command Mars plas 2 STAEDT Problem 11. 5 For normally consolidated clay specimens, drained direct shear tests were conducted and the follow ina data were olbtained. Determine the drained angle of internal friction Ų or the clay. KPa 150 300 400 500 hla aa.4 44.6 59.8 blotto 11.6
A sloping line 392.40 m long was measured using a 50 m steel tape weighing 0.075 kg/m which was standardized at 15°C and 25 N pull. The difference in the elevation between the initial and end point was 2.25 m. If the measurement was undertaken with a temperature of 20°C and the tape was supported at both ends with an applied pull of 50 N. The cross-sectional area of the tape is 5.25 mm^2 and E=200GPa. Determine the corrected length of the horizontal line.
e 120 m GL. 118 m GWL (2) A ground soil profile is shown in the right 7 Y =19 KN/m³ Y-21 KN/m³ figure. Soil layer information and their unit weights clay v 116 m are presented in the figure. The groundwater level Y-20 KN/m³ sand is 2 m below the ground surface. Find the vertical 111 m. effective overburden aressure and plot its clay Y=21 KN/m³ distribution curve. 107 m.
A soil profile is shown in Figure ?-?. Compute the shear strength on the horizontal and vertical planes at points ? and ?.
Q.6 Estimate the quantity of earthwork for given profile in the figure -2 for the the formation level 78.5 m. Use suitable method to solve. 12 .78.7 12 79.2 79.2 78.5 78.3 78.0 78.7 78.0 79.2 78.3 78.3 78.5
What is the greatest slope angle (B) of a slope formed by a cohesionless (C=0) sand? Assume the friction angle of the sand, o'= 28° O a. 280 Ob 350 OC. This sand cannot form a slope Od. Information is insufficient to determine
Briefly explain the meaning of FS = 1.0 for sand followed by the infinite slope analysis.
For the soil element shown, compute the stresses acting on the plane inclined by 40" with the horizontal plane then draw Mohr circle and place the stresses with respect to O.P. 20kPa 35kPa 100kPa 30 40°
What is the shearing strength of soil in kPa along a horizontal plane at a depth of 4 m in a deposit of sand having the following properties: Angle of internal friction, ∅ = 35°; Dry unit weight, yd = 17 kN/m3 ; Specific gravity, Gs = 2.7; Assume the ground water table is at a depth of 2.5 m from the ground surface a.11 b.95 c.23 d.41
Find the value of passive earth pressure coefficient if the angle of shearing resistance as 26 degree
3500 kN 3 m x 3 m 0.6 m Ya = 17.5 kN/m³ Sand 0.6 m GWT Sand Ysat = 18.3 kN/m3 1.2 m Y sat = 17.1 kN/m³ C, = 0.06 Clay 1.2 m e, = 1.4 Cc = 0.38 %3D