Question 27 An A36 angle bar is used as a tension member connected on both legs with 18 mm diameter bolts. Given that s = 65 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm

Q: Under reinforced section...define

A:

Q: What are the steps in LOTO in Construction OSH?

A:

Q: A 4 meter long steel plate with a rectangular cross section (10 mm x 50 mm) is resting on a…

A: Length of a steel plate, L =4 m Dimensions of plate = 50mm x 10mm Modulus of elasticity=200 GPa…

Q: The beam has an internal hinge at C. Express your answers in kN. Solve for the reaction at A.

A: A) Given data : To Find : Reaction at A ? A problem of Structure.

Q: what are the pros and cons and which one is better for a parking lot: porous asphalt vs pervious…

A: What are the pros and cons and which one is better for a parking lot: porous asphalt vs pervious…

Q: Observed N-value of an SPT test is 21. The N-value after correcting for dilatancy is 1. 18 2. 21 3.…

A: Given: Observed N-value of an SPT test, No=21.

Q: Q.2 Vessels A and B contain water under pressure of 276 kPa and 138 kPa, respectively. What is the…

A:

Q: Problem 1: Determine the flexural strength of a W 410 x 67 beam with a simple span of 8 m and Fy =…

A:

Q: 7 Link BD is made of brass (E = 105 GPa) and has a cross-sectional area of 240 mm². Link CE is made…

A: The give beam is analyzed by using the equation of equilibrium equations. The algebraic sum of the…

Q: e) Bx (no need to indicate direction since this is an internal force) f) Net force in y-direction at…

A: A frame is hinged at  A and C and an internal hinge is present at B   To determine,  The internal…

Q: Problem Sets: 2) The rectangular wood beam is loaded as shown in the figure. Determine the largest…

A:

Q: Define 'Shape factor'. Determine the shape factor of an I-section which is symmetrical about…

A:

Q: PROBLEM 3 Determine the centroidal moment of inertia, Ixx of the cross section shown. 6 in H .5 in…

A: Built up section is given and it has been asked to determine moment of inertia about x axis. Please…

Q: W = 3650 Kg/m ↓↓↓↓↓↓↓↓ 9m W = 4925 Kg/m 7.20 m ////

A:

Q: Buses vs Light Rail Transit Describe the culture impact these have.

A: Buses and light rail transit (LRT) can have significant cultural impacts on a community. Here are…

Q: A cylindrical tank (Figure 2) of diameter 50cm connected to a horizontal pipe (diameter is 8 cm)…

A: Given Data  Inlet velocity (Vi) = 5m/s = 500 cm/s  Outlet velocity (Vo) = 3.5m/s = 350 cm/s…

Q: ts Question 13 of 25 A reservoir of glycerin has a mass of 1200 kg and a volume of 0.952 cu.m. Find…

A: Given Data  Mass of glycerin (M) = 1200 kg  Volume of glycerin (V) = 0.952 m3  Determine the…

Q: Question 4 (1 point) L (ft) w (k/ft) Alimit= L/300 Sy = 36ksi Steel For a W21x50 W-section beam with…

A: Solution: Given: w=2.9k/ft=0.532784lb/inch          1k/ft=0.184lb L=10.ft=126 inches For given…

Q: The beam shown in Fig. 1 with uniform flexural rigidity El is subjected to the two concentrated…

A:

Q: 3.7-2 A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (a) If the shaft has…

A:

Q: Water (p = 1000 kg/m³) flows horizontally through a nozzle into the atmosphere under the conditions…

A: Given data- Density of water- ρ=1000 kg/m3At section-1A1=10-3 m2V1=2 m/sP1=3×105 Pa(gauge)At…

Q: The population of Angeles City in 1829 when it became a separate town from San Fernando is known to…

A:

Q: 6. Describe and provide and example of the most appropriate situation for the following: a) but-for…

A: As per the guidelines, I will answer the first question only. Please upload other questions as a…

Q: A C250 x 30 American Standard channel beam is supported and loaded as shown here. When z = 1 m and 8…

A:

Q: 1. Determine the internal determinacy of the given beam below. If determinate, solve for the…

A: A continuous beam is supported at point A ,B, C and D with hinged support at A and roller support at…

Q: SOLVE please Determine the design bending strength of ISLB 350 @ 486 N/m, considering the beam to be…

A:

Q: -29. Draw the shear and moment diagrams for the beam. 10 kN L₁ -3 m 5 kN/m 6 m- B 3 m- 10 kN

A:

Q: A municipality plans to treat 2.7 ML/d of a groundwater that contains 85 µg/L of…

A: Given, Q=2.7MLD D=3.66 m W=9000 kg γb=450 kg/m3 K=470(μg/g)(L/μg)1/n 1n=0.515 Influent…

Q: W BL L A C (hinge) L L D W E L F W=33 kN/m L=1m. What is the magnitude (positive value) of the…

A:

Q: A shear vane of 7 cm diameter and 11.0 cm length was used to measure the shear strength of a soft…

A: Given that :- diameter = d = 7 cm length = H = 11.0 cm Torque = T  = 700 kg-cm Find the shear…

Q: Consider a linear sinusoidal water wave with wave length 140m and 3-m wave height at 30m water…

A: Given Length =140m Wave height=3m Water depth=30m Sea-water density=1025kg/m³ To find The total…

Q: 3 - The strain gauge rosette indicated in the figure provides the following readings: &o= 400μ, E60=…

A:

Q: C If after many years of operation at Re = 105, the pipe's inner surface becomes rough with an…

A: Given, Re = 105  Roughness height, ε = 0.2 mm    NOTE : From recommended matches,     Velocity when…

Q: 23. The gasoline tank of a car contains 50 liters of gasoline and alcohol, with alcohol comprising…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: (a) Check if the given connection follows the code provisions on spacing and edge distance limits.…

A: Answer (1) Check for Maximum and minimum spacing Minimum spacing As per AISC Manual 14 edition…

Q: Why is safety and health the foremost professional responsibility of the engineer? Discuss in…

A: As an engineer safety and health are the primary responsibilities of the profession. It is because…

Q: Construction cost of the manufacturing plant is considered as overhead cost. True False

A: Explanation :  The construction cost of the manufacturing plant includes direct and indirect costs…

Q: C 1.5 m B 950 Nm 0.7 m 50 mm A The rod shown above is composed of two connected segments: AB is…

A:

Q: re Question 14 of 25 A lead cube has a total mass of 80 kg. What is the length of its sides if SG =…

A:

Q: A 3.7 m W 12 x 96 (Fy = 345 MPa) is used as a beam-column in a braced frame. It is bent in a single…

A: Given:- The steel section used W12×96  The yield strength of the steel = 345 MPa The magnitude of…

Q: What are the sources of Ignition? Explain each.

A: Ignition is the process of initiating combustion or a fire. It occurs when a source of heat, flame,…

Q: Calculate the steady-state recharge rate, and find how long would it take for dissolved road salt to…

A: Given data: Hydraulic conductivity, k(z)=0.5+0.03z Porosity, n=0.23 Depth of unconfined aquifer=-11m…

Q: 9. In this location of the highway 100 vehicles arrive in an hour. For analysis purposes, we are…

A: Given:- Number of vehicles arrive in an hour = 100 vehicles/hour A minute count is considered To…

Q: 1. A wastewater is treated in an aerobic CSTR with no cell recycle. The following hold: Ks= 50mg/l;…

A:

Q: 2. A Newtonian fluid is contained between parallel plates 0.1cm apart. (a) Find the rate of angular…

A:

Q: 3.) Average: Area Moment Method Given the Compound Beam as shown below. Determine load P that will…

A:

Q: 1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: A stress element is given with stresses shown. Young's modulus of elasticity, E = 80GPa Possion's…

Q: *Determine (a) the principal stresses, (b) maximum shear stress, and (c) the orientations of the…

A:

Q: Q-5 Water is supplied to a city having a population of 1 lakh at a constant rate of 150 litres per…

A: Given data- Population = 1 lakh, Flow rate of 150 liters per capita per day, Surplus is maximum at 7…

Q: H 2.27 Link BD is made of brass (E = 105 GPa) and has a cross-sectional area of 240 mm². Link CE is…

A: Given Data -  E of brass = 105 GPa  Area of Link BD = 240 mm2  E of aluminium = 72 GPa  Area of link…

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).