Question 2: (CLO 1 and 2) Consider a system h, shown in Figure, which is constructed from four LTI subsystems hı, h2, hs and h4. The following impulse responses are known hi[n] = 38[n] h2[n] = 38[n] - d[n-1] + d[n-2] h3[n] =-8[n] + 8[n-1] + d[n-2] ha[n] = 0.8"'u[n + 1] h2 x[n] y[n] hl h4 h3 a) Find and draw y[n] for n<10 if x[n]= õ[n] b) Check system is stable or unstable

Question 2: (CLO 1 and 2) Consider a system h, shown in Figure, which is constructed from four LTI subsystems hı, h2, hs and h4. The following impulse responses are known hi[n] = 38[n] h2[n] = 38[n] - d[n-1] + d[n-2] h3[n] =-8[n] + 8[n-1] + d[n-2] ha[n] = 0.8"'u[n + 1] h2 x[n] y[n] hl h4 h3 a) Find and draw y[n] for n<10 if x[n]= õ[n] b) Check system is stable or unstable

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A discrete time signal x[n] is given in Figure 1. Find the output y[n] by convolution if input x[n] in Figure 1 is applied to the below LTI system H where impulse response is h[n]=u[n+1]-u[n-2]-ô[n-1]. Draw y[n]. x[n] H y[n] x[n] 5 4 3 2 1 -3 -2 -4 00 -1 -1 -2 -3 -4 -5 Figure 1: x[n] 2.
Please solve the following problem showing all steps and explanations. I'm not quite sure what it means by comparing the two sensitivities of the transfer functions. This is just practice for an upcoming exam
(c) A linear time (shift) invariant system is shown in Figure Q1(c) with q[n], p[n] and r[n] represent the impulse response, the input signal and the output signal of the system respectively. The following difference equation defines the system: r[n] = 4p[n] + 3p[n 1] - 3p[n - 2] + 2p[n-3] (i) (ii) Find and draw the impulse response q[n] of the system. Compute and draw the output response r[n] of the system given the input signal p[n] = [1 2 3 1]. (iii) Discuss and show that the output response of the system r[n] can also be obtained using the circular convolution operation between p[n] and q[n]. p[n]. q[n] Figure Q1(c) ►r[n]
Q2: Answer A or B A: Simplify the block diagram shown below and obtain the closed-loop transfer function C(s)/R(s). G₁ R(s) C(s) G₂ H₁ H₂
What is the impulse response of the difference equation below: y[n] = ax[n−3] − by [n−1] y[n] = ax[n−3] − by[n−1].
Can someone please explain how to solve the problem below?
The operational amplifier in the circuit below has the following performance characteristics: Input offset voltage Maximum voltage swing Gain Bandwidth Product +/-3mV max Rail-to-rail 900 kHz Slew Rate 1.5 V/ms The circuit has the following component values • RI 4ΚΩ R2 8ΚΩ 4+14v v1 cos (2 nft> Vout U1 -140V (a) The input is a sinusoidal source as shown. What is the maximum allowed value for the input amplitude V1 before the amplifier starts to clip? (b) What is the expected bandwidth of the amplifier circuit? (c) What is highest possible DC level (offset) at the output.
Q19 Needed to be solved this question correctly in 20 minutes in the order to get positive feedback Please solve this question quickly in the order to get positive feedback hundred percent efficiency needed
Solve all subparts correctly please. I will Upvote if correct.
Consider the system shown below, with the following: G₁ = 1s², G₂ = 10.5/s, G3 = 9s, and G₁ = 9/ s, then: R(s) GF R(s) C₁ = 1 1- Reduce the system to a unity feedback one, if the forward transfer function takes the form C₁S²+C₂S+C3 Find the following: C₁S²+C5S+C6 = C₂ = 91.5 C3= 81 C₁= 162 C5= C6= 0 x x GF x GI G3 G2 C(s) G4 C(s)
A plant has the open loop transfer function shown below, with unity negative feedback and step input, after Using Matlab to plot the step response of the closed loop system, the output run is: G(s)=25/(s(s+4)) * Step response 1.4 1.2 0.8 0.6 0.4 0.2 3 10 no one of them the green plot the red plot the blue plot
Assume Is = 8 x 10-16 A, B = 100, and VA =0. For the circuit shown below and for I,= 3 mA, the value of the transconductance is Vcc=2 V Q1 VB Select one: O a. 115.38 mA/V O b. None of these O c. 38.46 mA/V O d. 19.23 mA/V O e. 76.92 mA/V