Question 2 a. Figure 1 shows a block diagram of a DC drive system. Diode rectifier AC supply Power converter SCR Firing circuit Regulator Operator's control station Constant-level DC voltage Variable DC voltage Current (torque) feedback Armature Voltage (speed) feedback Fig. 1: DC Drive System Describe step by step the principle of operation of the system. Shunt field

Question 2 a. Figure 1 shows a block diagram of a DC drive system. Diode rectifier AC supply Power converter SCR Firing circuit Regulator Operator's control station Constant-level DC voltage Variable DC voltage Current (torque) feedback Armature Voltage (speed) feedback Fig. 1: DC Drive System Describe step by step the principle of operation of the system. Shunt field

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 5-hp 230-volt shunt motor takes 18 amp when operating at full load. The shunt field resistance is 115 ohms and the armature resistance is 0.25 ohm. Calculate the value of the starter resistor if the armature current is limited to 1.5 times the rated value at the starting instant. (Assume a 3-volt brush drop.)
b) A DC shunt motor has an armature resistance of 0.2 22, a field resistance of 2002 and is connected to a 200 V supply. i) Draw the equivalent electrical circuit of the motor ii) If the motor runs at 1500 rpm and takes a current of 11 A from the supply, calculate the output torque of the motor iii) If the supply voltage is kept constant but the load torque is changed so that the supply current decreased to 6 A, determine the motor speed and the output torque.
The parameters of a three-phase, 50 Hz, 6-pole, 400 V star connected induction motor are r1 = 0.3 ohm, x1 = 0.5 ohm, r’2 = 0.15 ohm and x’2 = 0.2 ohm. The voltage and frequency of the induction motor is controlled by a power electronic converter (inverter). Calculate the required inverter output frequency and voltage to drive the induction motor load at 0.2 the rated speed of the motor and calculate the current drawn by the motor for that case. The formula for the maximum slip is given below:
Q2) A- Draw only Mechanical characteristics of the following special motors (Torque / Slip ): i- Hysteresis motor (ii) Stepper motor (iii) Servo motor (iv)Linear motor (iiv) SRM (vi)Performance curve for PMDC motor.
power electronics and drives
Design a simple ON-OFF transistor switch to control a 12 volt DC motor
f) Write the mathematic expresion for the Series Injected Voltage in UPFC for the following control cases: a) Voltage Regulation: b) Impeadance Compensation: c) Phase Shifter:
I need the answer as soon as possible
A 0,9 kW DC shunt motor is loaded by a constant torque of 12 Nm. The armature resistance of the motor is 5 Ω, and the field constant KØ = 3 Vs/rad. The motor is driven by a half wave thyristor converter. The power source is a 140 V, 50 Hz. The triggering angle of the converter is 450 and the conduction period is 1650 . Calculate the motor speed and the developed power.
7. The following table relates to the open-circuit curve of a shunt gen- erator running at 750 rev/min: Generated voltage (V) Field current (A) 10 172 300 360 385 395 0 1 2 3 4 Determine the no-load terminal voltage if the field circuit resistance is 125 N. If the speed is now halved, what is the resultant terminal voltage? At the reduced speed, what value of field circuit resistance will give a no-load terminal voltage of 175 V? (N.C.T.E.C., O.2)
Q1a
An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KĘ = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax 2. Plot the following relationships: (i) Torque versus current (ii) Induced voltage versus speed 3. If the above motor is operated at 3000 rpm with a load torque of 0.15 N.m, determine the armature voltage