Question 1: The simply supported beam shown below of span 7 m supports a mid-span concentrated service live load of 100 kN and a uniformly distributed service dead load of 30 kN/m in addition to its own weight. Determine the required spacing of 10 mm stirrups at the critical section for shear.Use Fc = 30 N/mm², Fy = 350 N/mm², Ycone= 24 kN/m³. Wu (kN/m) Pu (kN) -7.0 m -300- 700 ah 10

Question 1: The simply supported beam shown below of span 7 m supports a mid-span concentrated service live load of 100 kN and a uniformly distributed service dead load of 30 kN/m in addition to its own weight. Determine the required spacing of 10 mm stirrups at the critical section for shear.Use Fc = 30 N/mm², Fy = 350 N/mm², Ycone= 24 kN/m³. Wu (kN/m) Pu (kN) -7.0 m -300- 700 ah 10

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1 Figure 1 shows a continuous beam fixed at A and has simple supports at C and E. Using the static equilibrium method, determine: a) The degrees of indeterminacy for the structure. b) The number of possible plastic hinge locations. Also list their locations. c) The number of independent mechanisms. d) The required value of Mp to ensure a minimum load factor =2.5 for any span. 10A kN 201 kN А В C D E Mp Mp 2 т 2 т 2 т 2 m Figure 1
Problem 13.2: For the beam shown in the figure below, determine the maximum bending stress. Misan Univers F4 i. of in. 14.0 kN 1.5 kN/m in.-- 3 in. 송 In. -1.0 m-1.0 m 2.0m 2 in.
Situation 1. A simply supported beam of cross section 200 x 400 mm has a span of 12m. It carries a uniform load of w = 21.5 kN/m starting from the left end and terminates at midspan. Consider E = 200 GPa immmmmm 1. 2. 3. What is the resulting deflection (mm) at midspan? To prevent excessive deflection, a support is added at midspan. Compute the resulting moment (kN-m) at the added support. To prevent excessive deflection, a support is added at midspan. Compute the resulting reaction (kN) at the added support.
5. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0.680 KN/m including its own weight. Use fy-276.50 MPa and fc'=20.70 MPa. The ultimate load that the beam can carry is _KN-m. 12.905 O 15.942 O 20.541 O24.038 O29.473 33.681
A cantilever beam AB with a circular crosssection and length L = 750 mm supports a loadP = 800 N acting at the free end (see figure). Thebeam is made of steel with an allowable bendingstress of 120 MPa.(a) Determine the required diameter dmin (figurepart a) of the beam, considering the effect of thebeam’s own weight.(b) Repeat part (a) if the beam is hollow with wallthickness t =d /8 (figure part b); compare thecross-sectional areas of the two designs.
A cantiliver beam subjected to a uniform load along its length and axial load P. Draw the shear and determine the maximum shearing force. Determine the maximum shearing stress of the rectangular beam made of narra having dimension of 225mm x 450mm (b, d) P=10KN W =4kN/m A B 6.0m
No. 3. Beam AC carries a concentrated load P at its midspan point B. Determine the depth of the beam h in mm if the maximum bending stress is Omax = 50 MPa, the maximum deflection 8max = 10mm, the span is L = 4m, and the modulus of elasticity is E = 200 GPa. L/2 L/2- B 4+ 18. max
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given beam and loading. Given: h = 0.3 m 15 kN 25 kN 20 kN A су D E B h 1m-7 0.3 m 30 kN 0.4 m If the distance between E and Bis h= 0.3 m, calculate the maximum absolute values of the shear and bending moment! The maximum absolute shear force Vmax is The maximum absolute bending moment MImax is KN on CD kN.m at B
4. Investigate the adequacy of the beam reinforced for tension and compression as shown. The total load is 30 KN/m including its own weight, fc' = 20.7 Mpa, fs = 138 Mpa, and n = 10. 65 mm 50 KN 3-32 mm Ø w = 30 kN/m 370 mm 500 mm A B C 3-32 mm Ø 65 mm 300 mm 4 m 3 m 3 m 2 m
20. A CIS33.9 of A36 channel to serve as a roof edge beam with a simple span of 25 ft. The nominal loads are a uniform dead load of 0.23 kip/ft and a uniform live load of 0.69 kip/t. The beam is continuously braced. If =315 in, what is the live load deflection at the center of the beam? A) 0.534 in B) 0.766 in C) 0.664 in D) 0.693 in
4. A 10 m span simply supported beam carries a uniform load. The beam has an adequate lateral support. ALLOWABLE STRESSES: Bending: 12.65 MPa Deflection: 1/240 of span E: 13000 MPa a. Compute the depth of the beam so that when the allowable stresses of 12.65 MPa is reached, The deflection of the beam is 1/240 of the span. b. If the width of the beam is 300mm, how much total uniform load can it simply support? c. Compute the shearing stress of the beam using the uniform load in letter b. W (kN) lom 12 R
A Universal beam of I shaped cross-section is 203 mm deep, and 133 mm wide and has a steel plate 150 mm by 10 mm thick fastened to each flange. Ix-x for the universal beam is 28.80×10^6 mm^4. a) Determine the total uniformity distributed load which may be carried over a simply supported span of 6 metres if the permissible bending stress is 165 N/mm^2. Neglect the self-weight of the beam. [Ans.: 124.02 KN/m] b) Determine the minimum central length over which the additional plates are required. [Ans.: 4.23m]