Question 1 of 20 : Select the best answer for the question. 1. The NEC states that the neutral conductor of a three-wire branch circuit supplying a household electric range with a maximum demand of 8.75 kW shall be permitted to be smaller than the ungrounded conductors. However, the neutral ampacity shall not be less than percent of the branch-circuit rating and shall not be smaller than 10 AWG. O A. 70 O B. 30 OC. 50 O D. 8.75

Question 1 of 20 : Select the best answer for the question. 1. The NEC states that the neutral conductor of a three-wire branch circuit supplying a household electric range with a maximum demand of 8.75 kW shall be permitted to be smaller than the ungrounded conductors. However, the neutral ampacity shall not be less than percent of the branch-circuit rating and shall not be smaller than 10 AWG. O A. 70 O B. 30 OC. 50 O D. 8.75

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.1: Counter-mounted Cooking Unit Circuit

Problem 6R

See similar textbooks

Similar questions

1. Bus bars in electrical substation are made of aluminum because it has i Low cost ii. Low Density ii. High Resistivity iv. Low Melting Point 2. is the greatest demand of load on the power station, during a given period. 3. The arc resistance in circuit breakers doesn't depend on i. Length of Arc ii. Degree of Ionization iii. Cross section of the Arc i. Cross section of the Conductor 4. List out any two limitations of fuse. 5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor iü. Voltage at points B and C ii. Point of minimum potential
Question 3 (a) Discuss and critique the law of electricity supply? (b). Explain with a diagram a Retail competition model of electricity market. (c). Explain effects when government has a bigger say in the operation of Public utilities.
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
cal Power Syste Courses / EEPW2252/ Assessments / Quiz-2-Section 4 Mr. Raqib Hussain The resistance of the conductor increases with increase of Temperature. Select one: O True O False
At low powerfactor the power system has _______________________ a. less losses b. more voltage c. more current d. more efficiency
QUESTION 5 We would like to run the power wires for both cooling pumps in the same RMC from the Breaker panel to a junction box above the control panel. What size ungrounded conductors do we need for the 100 amp load? All conductors have typeTHHN insulation. A #6 AWG B #3 AWG C #4 AWG D #1 AWG
Figures / Diagrams, equations and solving of problems should be written by hand. Take a picture of it and attach it inside the word file. a) High Voltages are preferred for Transmission of Electricity. Why? b) Why Generation Voltage Levels are low in the range of 11 kV/ 33 kV etc? c) Why ACSR Conductors are preferred over Copper Conductors? d) Overhead Transmission Lines are preferred for Transmission of Power for Long Distances, why? e) Alternating Current is preferred over Direct Current in Power System, Why? f) Write the Installed Generation Capacity of Sultanate of Oman with current energy share of Conventional and Non-Conventional Energy Sources. g) Why the Capacitance effect is neglected in Short Transmission Line. h) Distinguish between Lumped or Distributed elements in a Transmission Line.
QUESTION -7 In the following figure a power line to drive a Load is represented. The wires are made of copper and shaped as solid round. Under the following requirementsi. The length of each positive voltage and ground wire is 30ft.ii. The maximum allowable resistance of each power line is 0.006 Ω.iii. The maximum allowable current is 110A for each power line.Find the followinga) Using the AWG table (given in this exam sheet) find the suitable cable type with minimum size.b) Considering power supply as E=24V and current drawn by the load as I=12A, find the total voltage drop over the cables and voltage difference over the Load.
a) In a Power System, Define the following (i) Peak Load (ii) Spinning Reserve b) With a neat diagram, explain the working of the Solar Power Plant? 2. What are the various types of Line supports of the transmission line? Draw a neat sketch of any one type. Please do not write the answer on a paper
Question 5 - Power Network, Frequency & Connected Load a) In the UK and many other countries, there are legal requirements to maintain voltage and frequency within permitted tolerances. Explain why it is important to keep the electrical system within these tolerances.
You are a journeyman electrician in an industrial plant. You have been assigned the task of connecting a 25-kW electric heater to a 240-V, single-phase panel. The heater is located in an area with an ambient temperature of 90°F. The conductors are to be copper with Type TW insulation. The heater is expected to operate for more than three hours at a time. What size conductors would you use to connect this heater? Is this correct? I=P/EI=25000 W/ 240 VI= 104.17 amps x 125%I= 130.21 amp/ .96I= 135.63 amp2/0 AWG conductor will be needed
5 a) Discuss Electricity power generation and distribution to residential properties. b) with diagrams explain how a Distribution Board is wired to provide electricity to a residential property. c) Explain the following materials and Accessories. i. Male and female bushings. ii male and female adaptors iii. Couplings. iv. Wire/cable sizes and their us