Question 1: For the shaft subjected to the applied torques as shown, determine the angle of twist of end A relative to point C according to the given axial x axis. End D is fixed. D 1 = 40 mm G= 26 GPa 40 N m 100 N m 1m 1m 1 m 60 N-m (a) -3.83x10-4 rad (b) 3.83x10-4 rad (c) 2.23x103 rad (d) 3.06x10-3 rad

Question 1: For the shaft subjected to the applied torques as shown, determine the angle of twist of end A relative to point C according to the given axial x axis. End D is fixed. D 1 = 40 mm G= 26 GPa 40 N m 100 N m 1m 1m 1 m 60 N-m (a) -3.83x10-4 rad (b) 3.83x10-4 rad (c) 2.23x103 rad (d) 3.06x10-3 rad

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q12 (Simple stress and strain) Item 3 of 3 A bar AB (A = 500 mm?) is hinged at A and is supported by a rod CD and C. The rod is pin connected at A, as shown. Neglect deflections of the bar due to bending. If the diameter of the rod connecting the load W = 90 kN is 20 mm, what is the displacement of the load? Use E=210 GPa. (10 38 mm. 2m 1.8m ww Diameter TYOR 2.5 m 1.5m 0.6m W=90kN
-13-24. An L-2 tool steel link in a forging machine is pin connected to the forks at its ends as shown. Determine the maximum load P it can carry without buckling. Use a factor of safety with respect to buckling of F.S.= 1.75. Note from the figure on the left that the ends are pinned for buckling. whereas from the figure on the right the ends are fixed. 1.5 in. 0.5 in. 24 in. Prob, 13-24
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
A solid 30.0-mm-diameter steel [E = 290 GPa] shaft supports two pulleys as shown. Determine the shaft deflection at point C. Assume that the bearing at point A can be idealized as a pin support and the bearing at point E can be idealized as a roller support. ... A B D E C 300 mm 200 mm 300 mm 200 mm 750 N 500 N (A -1.101 mm -0.936 mm -0.876 mm D) -1.586 mm E) -0.697 mm
Question #4: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and Eb = 105 GPa, determine (dsteeF 40 mm, dbrass = 30 mm) 1- The reactions at A and E. 2- The deflection at C. 180 B 120 * 60kN 100 100 40 RN D Steel Brass Dimensions in mm.
Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40 MPa and in compresion is 80 MPa. 4kN 4KN. 220 16KN N. A 大 6m 'RB INA: 4 = 20* (o mm
3/98 Each of the three uniform 1200-mm bars has a mass of 20 kg. The bars are welded together into the configura- tion shown and suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to the x-z plane. Compute the tension in each wire. B 600 mm 1200 mm A 30⁰! 1200 mm PROBLEM 3/98 600 mm -y
d₂ d₁ B A P X2 X1 A load P = 54 kN is applied at end C of the brass rods AB and BC. If E= 115 GPa, determine the diameter d1 of rod BC for which the deflection of end C from the fixed end A is 6 mm, after the load is applied. Use the data below to assist: x1 = 0.75 m x2 = 1.30 m d2 = 29 mm Calculate your answer to two decimal places. Report your answer in millimeters (mm). Use the same unit as d₂. Hint: Consider how the rods AB and BC are connected.
< Engineering... 700 lb 400 lb TITLEITE 11. The rectangular plate is made up of 1-ft squares as Shown. A 30-lb force is applied at point A in the direction shown. Calculate the moment of the force about point B by at least two different methods 1 ft I 1 ft -x B P = 30 N 1.6 m A 12. The 30-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment Of P about point B and about point A. B A 45° □ Q : 30 lb 1.6 m D/TU 4/16
3- For the beam given in the figure, a- Draw the elastic curve by using the Mohr Method. Calculate the values of A, B, VC, ec by using the Mohr Method. b- A 2EI 3 m B 3EI C I1m] 60Nm
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
Q2. A rigid bar AB is supported by a hinge at A and by a steel wire T as shown. With no load applied on the bar, the end B is 2 mm above the contact point C. Determine where a W=390 N load should be placed on the bar so that the end B will just touch the support at C. For the steel wire E=200 GPa. 300 mm 100 mm T STEEL WIRE D=2.50 mm E=200 GPa 400 mm W B Y 2 mm A