Question 1 A 50 kN load is transferred from a welded fitting into a 200 mm Figure 1. steel channel as illustrated in 6|- - 200- 50 kN 100 9A 19 56 200 C 190 Figure 1 a) Label the ends and corners of each welded by letter. b) Estimate the primary shear stress . c) Sketch the stress at each lettered corner or end. d) Locate the centroid of the weld pattern and hence, find the distance between the centroid and lettered corners and ends.

Question 1 A 50 kN load is transferred from a welded fitting into a 200 mm Figure 1. steel channel as illustrated in 6|- - 200- 50 kN 100 9A 19 56 200 C 190 Figure 1 a) Label the ends and corners of each welded by letter. b) Estimate the primary shear stress . c) Sketch the stress at each lettered corner or end. d) Locate the centroid of the weld pattern and hence, find the distance between the centroid and lettered corners and ends.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(7) The permissible shear stress for the weldment illustrated is 140 MPa. Estimate the load, F, that will cause this stress in the weldment throat. (Ans.) 49.2 kN) 163 200 Dimensions in millimeters
7) For double side parallel fillet weld subjected to an external force 100 kN. The weld has throat thickness of 5 mm and the measured shear stress is found to be 100 MPa. From the above given information find out the length of the welded joint desigN? O 100 mm 50 mm 25 mm 10 mm
A cylindrical air-compressor tank with an inside diameter of 50 mm is to be designed to withstand safely a working pressure of 0.86 MPa. Boiler plate with an allowable tensile stress of 76 MPa. All seams will be butt welds with an expected efficiency of 100 percent. a.) Determine the force per lineal mm of longitudinal seam, b.) Determine the required thickness “t” of wall, c.) Determine the unit stress in the circumferential seam.
4) Determine the maximum stress. in the welds an if the joint.is. Safe for T=90.N/c. for figurea te h= {mm ム=6mm Ans: て 300N 15cm 5cm 20 Cm 18Cm
3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding connection. The length of weld shown in the picture is 300 mm on the top and 100 mm on the bottom. The 2-L127x 89x6.4 are 300W steel and long leg back-to-back. The braces are to be welded to a 12 mm 350W steel gusset plate. Determine the factored tensile capacity of the angles. Any intermediate connections that are required should also be specified. 740 kN -12 mm Gusset Plate
2. The figure shows welded hand rotates a shaft via a key. The key material allowable shear strength is 150 MPa and crushing strength is 300 MPa. The welding material yield strength is 340 MPa. F 350 N a) Calculate the key length. |L1 1075 mm b) Calculate the factor of safety of the welded joint L2 1125 mm D1 25 mm L2 B 8 mm F H 7 mm h 4 mm X1 40 mm X2 40 mm
Not yet answered Marked out of 1.00 P Flag question Arectangular cross-section bar is welded to a support by means of fillet welds as shown in Figure below. Determine the size of the welds, if the permissible shear stress in the weld is limited to 75 MPa. 25 kN 500 -150- 100 All dimensions in mm
QUESTION 3 2. For the given welded bracket shown, design the required size of weld needed to resist the given eccentric load P=125 kN. Use E70xx electrode. Where: X=150mm, Y=125mm, Z=50mm what is the maximum force on the welds in kN? (2 decimal places) X Y
A welded joint on a mining machine is subject to cyclical stresses with a nominal stress range of 50 MPa. The detail category is identified as 56. The maximum plate thickness for the adjoining members is 20 mm. The weld is a SP Category full penetration butt weld and a capacity factor 0.90 can be assumed. What is the expected life in terms of number of cycles according to AS4100? а) 9.25 х 104 b) 5.11 x 105 c) 7.33 x 106 d) 1.02 x 107 e) 2.05 х 106
Azt Qet If Chao.7 cm) for weld , fincd (Iimax) for figure blow: l00 225mm of f=400W 150mm 45.27 mlam? answer: Tomax
sheet Hw Asteel bar of rec tangular crossl seetion with dimension as -s hownin fig- belo .This bar is Connected toawell. Using welded Juin along the sides only- find the weld size Ch) .where: Tall= 75 N /m? answer h= 4.04 %3D %3D F=213.3 N yomm 50omm l0omm
a) list two advantages and two disadvantages of welded joints b) Name the type of bonding forces applied in welded joints A plate 50mm wide by 11mm thick is joined with another plate 120mm wide by 11mm thick by parallel welds of 40mm long.if the permissible tensile and shear stresses are 110MPa and 80MPa respectively calculate; i) safe load F carried by the joint ii) Efficiency of the joint