can someone answer question 2 for me. Answer both part A and part BUrgent!!!Circuits are provided 2. (a) Given the circuit shown in Figure 4.4a with V, = 5 [V], R1 = 4.7 [kN], R2 = 10 [k2], R3 = 3.3 [k!).and RL = 10 [kN]. You are to compute the current through and the voltage across the load resistorR1 using the Thévenin equivalent circuit analysis technique.%3D%3Di. Determine the Thévenin equivalent voltage VTH and resistance RTH.ii. Draw the Thévenin equivalent circuit diagramiii. Compute the current through and the voltage across the load resistor RL.(b) Given the circuit shown in Figure 4.4b with V,1 = 5 [V], V,2 = –5 (V], R1 = 3.3 [kſN], R2 = 5.6 (kl)|and Rg = 10 [ks2].%3D%3D%3D%3Di. Determine the Thévenin equivalent voltage VTH and resistance Rth.ii. Draw the Thévenin equivalent circuit diagram.iii. Assume that the load resistor R1shown in Figure 4.4b. Compute the current through and voltage across the load resistor R1-10 (k] is connected across nodes A and B of the circut%3DE Minh Rs I3A.R IR2VịV3V1VaAV,V2 R2V,1Vs R VTHRLIL(a)(b)Figure 4.4: Circuits used for determining Thévenin equivalent circuits.

Answered: Image /qna-images/answer/bab6bb07-5705-4dfe-8f39-2bb85e5ac01c.jpg

Answered: que. resistance RTH.

Engineering

Electrical Engineering

que. resistance RTH.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(c) A circuit shown in Figure Q4.c has an a.c. source of 50 V and internal resistance Rin 2 k2 is matched to a load by a 10:1 ideal transformer. Calculate the power dissipated in the load. a.c. source Rin NIN-101 Figure Q4.c
Problem 4 In the Wheatstone bridge circuit of Figure P4 determine.
B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
Please answer it with steps... Thank you. The theoretical values of the current through the resistor R2 in all the circuits shown in figures 6.1, 6.2, and 6.3 are taken from experiment number 5 (same circuits) which are as follows: I2 = ……….., I2’ = …………., I2” = …………..From superposition theorem, I2 = I2’ + I2” ⇒ ………. = ……….. + ………..
Calculate for point P4, P5 and P6 only.
Consider the circuits shown in figure 4. Each represents a configuration of LEDs driven by a voltage or a current source. For the purpose of this problem you can model the LED as a resistor. The intensity of the LED is proportional to the power dissipated by it. Suppose one LED burns out (i.e. becomes a open circuit), for each configuration shown determine if the intensity of the remaining LEDs becomes brighter, dimmer or stays the same. Support your answers with appropriate calculations. V (a) D ODDDDDD V (b) Figure 4: LEDs arranged in different configurations (c)
Solve for Vs and Pvs. Show complete solution.
How about solving this using KCL equations? Thank you
3. Discuss the limitations in the application of Kirchhoff's laws to railway and other power systems. In what manner do these circuits differs from the usual battery circuits in which the emfs and resistances only are given?
After solving for the total resistance, and the applied voltage being a given for the circuit, the next logical step is to .....? so that individual component voltages and currents can be found.
Fill the blanks with suitable following terms (AND gate, Potential Transformers (PT), cathode ray oscilloscope CRO, electronic switch Current Transformers (CT), DC component, cathode ray tube (CRT), AC component, electron.gun. 1.The heart of a ............is the................. the electron beam is generated, accelerated, and deflected in accordance with the input signal. 2. Power measurements in high-voltage high current circuit can be effectively done by the use of...and.. ...in conjunction with conventional wattmeter. 3. The sig ...ose frequency is to be measured is converted into a train of pulses (Using Comparator for example), one pulse for each cycle of the signal and applied continuously to an...A 4. In Average Responding Voltmeter, the AC signal is first applied to the blocking capacitor used at the input to block any..................in the input voltage. 5. Dual Trace Oscilloscope This CRO has a single.....................whose electron beam is split into two by an…