QUA65 Kw,3-phase ,Y-connected ,50HZ ,220V, cylindrical motor synchronous motor operates at reated condition with 0.6 p.f. leading .The motor efficiency excluding field and stator losses ,is 90 %and XS developed (ii) armature (v)maximum or pull-out torque of the motor. 20 .Calculate (i)mechanical power current (iii)back e.m.f. (iv)power angle, and %3D

QUA65 Kw,3-phase ,Y-connected ,50HZ ,220V, cylindrical motor synchronous motor operates at reated condition with 0.6 p.f. leading .The motor efficiency excluding field and stator losses ,is 90 %and XS developed (ii) armature (v)maximum or pull-out torque of the motor. 20 .Calculate (i)mechanical power current (iii)back e.m.f. (iv)power angle, and %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase, 10 MVA, Salient Pole, Synchronous Motor is run off an 11 kV supply at 50Hz. The machine has X = 0.8 pu and Xq = 0.4 pu (using the Machine Rating as the base). Neglect the rotational losses and Armature resistance. Calculate The maximum input power with no field excitation. The armature current (in per unit) and power factor for this condition.
A three-phase 60 Hz induction motor connected to a three-phase bus at rated voltage isoperating at a low slip condition (i.e s < 20%) resulting in a steady state speed of 1090 rpm.(a) How many poles does the motor have?(b) What is the percentage slip at the operating speed?(c) What is the corresponding frequency, (fr) of the currents and voltages induced in therotor winding?
A delta connected 1235 V, 50 Hz three phase induction motor has a star-connected slip-ring rotor with a phase transformation ratio of 4.2. The per phase rotor resistance and standstill leakage reactance are 0.0676 ohm and 0.031 ohm respectively. Assuming the stator impedance and magnetizing current are neglected. Calculate the the following, (i ) The rotor current at starting with slip-rings are short circuited. (ii) The rotor power factor at starting with slip-rings are short circuited. (iii) The rotor current at 3 % slip with slip-rings are short circuited. (iv) The rotor power factor at 3 % slip with slip-rings are short circuited. (v) The external rotor resistance per phase required to obtain a starting current of 65 A in the stator supply lines.
A three phase synchronous motor of 60HZ, has the stator winding with pitch angle of 90°, distribution angle of 20°, with number of slots per pole per phase of 20, and magnetic field flux density of 100mWeb/cm? spread over an area of 15 mm?. The number of turns in the stator winding is 1000. Calculate, i. Fundamental component of EMF induced in stator winding. ii. 2th order (harmonic) component of EMF induced in stator winding. iii. 4th (harmonic) component of EMF induced in stator winding. iv. RMS value of the EMF induced in stator winding
3-phase 3730W, 220V, 8 poles and 50 Hz asynchronous motor operates at full load with a slip of 0.025. The sum of the rotational losses including friction + windage losses and other (stray load) losses is 5% of the output power. Find the induced (electromagnetic) moment at full load.
A delta connected 1185 V, 50 Hz three phase induction motor has a star-connected slip-ring rotor with a phase transformation ratio of 4. 2. The per phase rotor resistance and standstill leakage reactance are 0.0627 ohm and 0.049 ohm respectively. Assuming the stator impedance and magnetizing current are neglected. Calculate the the following, (i) The rotor current at starting with slip-rings are short circuited. (ii) The rotor power factor at starting with slip-rings are short circuited.
A delta connected 1185 V, 50 Hz three phase induction motor has a star-connected slip-ring rotor with a phase transformation ratio of 4. 2. The per phase rotor resistance and standstill leakage reactance are 0.0627 ohm and 0.049 ohm respectively. Assuming the stator impedance and magnetizing current are neglected. Calculate the the following iii) The rotor current at 3 % slip with slip-rings are short circuited. (iv) The rotor power factor at 3 % slip with slip-rings are shot (v) The external rotor resistance per phase required to obtain a starting current of 145 A in the stator supply lines.
the step-by-step solution needed with calculation. 45) A 40hp, 440V, 4 pole dc motor has an armature wave-wound with 846 conductors and the commutator has 141 segments. The full load efficiency is 85% and the shunt current is 1.25A. If the brushes are shifted backward through segments from the geometric neutral axis, calculate (a) The demagnetizing ampere-turns per pole (b) The distorting ampere-turns per pole on full load. the previous one is wrong.
The armature resistance and armature reactance of a 3.5MVA, 11.5kV, Y-connected, 8 pole Synchronous Motor respectively are 60/phase and 200/phase. Determine the excitation voltage, power input, power output, total losses and efficiency at half of the rated load of machine and at a power factor of 0.7 leading. The total mechanical losses in the machine are 1.5kW and draw the phasor diagram. Write any assumptions made in doing above calculations.
Three-phase induction motor, 460 V 50 Hz, 4 poles, 50 hp with Delta, operating at 3.8% slip rated torque when receives Line Voltage 460 V, 50 Hz The parameters of the equivalent circuit per phase are as follows.R1 = 0.33, X1 = X2 = 0.42 and Xm = 30 Ohm / phase.Answer the following questions by neglecting the mechanical losses, Core losses and Stray load losses.A) Value of the rotor resistance R2 B) Maximum torque and rated speed C) line current and starting torque of motor
3-phase, 380V, 50HZ, 4-pole, Y-connected asynchronous motor's rated speed is 1380 rpm. The two ends of the stator terminals The resistance value between is measured as 150. It is known that the value of friction and wind losses is 33W. The values taken from idle running and locked rotor tests are given below. Accordingly, one phase equivalent of the motorDraw the equivalent circuit by finding the circuit parameters. idle test locked rotor test input power 220W 370W line current 1.82A 3.11A Line voltage 97V
For a 3-phase, 4-pole, 50 Hz synchronous motor the frequency, no. of poles, and the load torque are all halved. Then what will be the motor speed?