QI: For the network shown in figure(1), 1. find the mathematical expressions for vc and ic if the capacitor was charged with 15 and the switch is thrown into position 1. 2. Repeat part a, if the switch is thrown into position 2 at a time equal to three-time constants of the charging circuit. 3. Plot the waveforms of vC and ic for a period of time extending from 0 to 40us. + UR 60 V 1 470 kf 220 kN 22 nF

QI: For the network shown in figure(1), 1. find the mathematical expressions for vc and ic if the capacitor was charged with 15 and the switch is thrown into position 1. 2. Repeat part a, if the switch is thrown into position 2 at a time equal to three-time constants of the charging circuit. 3. Plot the waveforms of vC and ic for a period of time extending from 0 to 40us. + UR 60 V 1 470 kf 220 kN 22 nF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The formula used to fit ILED versus VLED was Y = a (1-e^-bx). Compare this equation to the shockley ideal diode equation. what is the parameters a and b?
b) A sine voltage trace displayed on a screen is shown in figure5. The x axis is 1unit=50 ms and y axis, 1 unit=2 V; determine the frequency of the sine wave and plot the waveform if the same is applied to the input of a half wave rectifier. V Figure5
The circuit below with an ideal diode is used to charge a 12 V battery. vin is a sinusoid with 24 V peak amplitude: vin = 24 sin(⍵t) a) For how long does the diode conduct within each cycle: 1/2 of the cycle time, 1/3 of the cycle time, ¼ of the cycle time, or 1/5 of the cycle time? b) Find the peak value of the diode current and the maximum reverse-bias voltage that appears across the diode.
From the diode circuit shown in Figure 1, show how to determine the resulting output voltage signal. Given the input voltage signal Vi it is as shown in Figure 1 on the left and the diode used in Circuit 1 is 1.1. Ideal diode 1.2. Diode using approximation model 10 ARA " t V₁ O 1kQ www 1k2 Figure 1 SI Z ww ΣΚΩ V₂ +15V
1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm=2k İm=(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances). R1 u(t) R2 1R3 18k 20k R4 k: k2 10k
Determine the state of the diode D1. Use Vp - .7V 5.n FUE-SU 7° √₂= you
Electrical Engineering please solve this thank you The following values are given for a shocdley diode Vi (derel vollaye) • 0.025 V Is (Deverse salunalia cmal): 10X10A -15 Given voltaye eg ^: v(t) = 0.7+ 8 Vr cosut IA RL= 50 0 %3D Find avg. powen diipted in shochly diode € ay.power deliveud to load
In the given circuit, (diodes will be considered ideal.a) Draw the V0 output by calculating it according to the input.b) Calculate the average and effective value of the V0 output.c) What are the advantages and disadvantages of using two diodes and two resistors instead of four diodes?Input signal Vm = ± 10V (peak to peak), T = 2π (period), R = 32k
Calculate the voltage and current of the diode in the figure for each of the diode's models. In each case, determine the voltage across the resistor. Additionally, in each case, determine the diode's power. Assume that Rb is ten ohms.
What is the dynamic resistance of a diode if its Ip = 4.06 mA? No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places.
Find the equivelent resistance of the circuit below. (Rin)Conduction diodes' resistance is 0Insulating diodes' resistance is infinite.R1 = 10 ohm
For circuit given in Figure 3 use Complete Diode Model andfind the voltage across R1 and R2 andtotal current flowing in this circuit. Giventhat diodeforward resistance is 15 Ohmsfor D1 and 10 Ohmsfor D2, also reverse current flowing acrossD2 is 20 micro Amperes. DI Ri 50 Q ww D2 Rz100 N KH 10 V R3150 2 www Figure 3