I need the answer as soon as possible Q1/ DC chopper with inductive of 10mH, supplies a load of 220 V from 120 V de supply. Ifconducting period of the thyristor to be 100 microsecond, fill in the blank with a correct value tofind :Duty cycle is*Your answerRMS output voltage is .Your answerpeak to peak load current isYour answertime ratio is*Your answer

Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Answered: QI/ DC chopper with inductive of 10mH,…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
3. The secondary voltage can rise above its rated value when the load is a. resistive. b. capacitive. C. inductive. d. an RL series combination.
If the voltage V, = 800 mV, then the current flowing in the load I, is: %3D -j20n Select one: O a. None of these O b. Is 100 <-90° mA O c. Is 5.0<.-90° A O d. Is 5 <90° mA ell
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
10. Determine the peak-to-peak ripple and de output voltages in Figure 5. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. A R surge 120 Vrms 00000 ellle B Figure 5. www 10 Ω C 100 μF www R₂ 3.3 ΚΩ
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). Choices: 0.11A 22mA to 89mA 9A 0.11A to 9A Plss show complete solution
In general, the greater the absolute value of the impedance in a circuit:A. The greater the flow of alternating current.B. The less the flow of alternating current.C. The larger the reactance.D. The larger the resistance.
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

QI/ DC chopper with inductive of 10mH, supplies a load of 220 V from 120 V de supply. If conducting period of the thyristor to be 100 microsecond, fill in the blank with a correct value to find: