Q9: The pitch of 50 mm mean diameter threaded screw of a screw jack is 12.5 mm. The coefficient of friction between the screw and the nut is 0.18. Determine the torque required on the screw to raise a load of P kN, assuming the load to rotate with the screw. Determine the ratio of the torque required to raise the load to the torque required to lower the load and also the efficiency of the machine.| Where, P= 46KN

Q9: The pitch of 50 mm mean diameter threaded screw of a screw jack is 12.5 mm. The coefficient of friction between the screw and the nut is 0.18. Determine the torque required on the screw to raise a load of P kN, assuming the load to rotate with the screw. Determine the ratio of the torque required to raise the load to the torque required to lower the load and also the efficiency of the machine.| Where, P= 46KN

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter10: Work, Energy And Machines

Section10.2: Machines

Problem 28PP

See similar textbooks

Similar questions

plve the problem. 1. You are using a wheel and axle as a simple machine. You applied a force of 30 lb to the rim of the wheel so that it can lift a load of 240 lb. The diameters of the wheel and axle are 3 feet and 4 inches, respectively. Determine the efficiency of the machine.
A steel rod 250 mm long and 200 mm in diameter is being reduced to 190 mm in diameter all over its length in one travel. The machine spindle rotates at 500 rpm, whereas the tool is moving at an axial feed of 0.5 mm/rev; calculate the following: a. Material removal rate (mm3/min) b. Consumed gross power in Nm/s if cutting force is 477.5N and mechanical efficiency is 90% c. Cutting time
A single-cylinder reciprocating engine has a reciprocating mass of 6 kg. the crank rotates at 60 rpm and the stroke is 32 mm the mass of the revolving parts at 16 mm radius is 4 kg, if two-thirds of the reciprocating parts and the whole of the revolving parts are to be balanced. Determine the balance mass required at a radius of 35 mm and unbalanced force when the crank has turned 50° from the TDC.
(a) Which component of the horizontal axis wind turbine can be considered as the brain of the system? Write the important functions of this component. Explain how it coordinates with the anemometer, wind vane and yaw drive for the proper working of turbine. I (b) Explain, why wind energy is considered as highly desirable and economical to the rural areas which are far from existing grids
A constant 20-N force pushes a small ball in the direction of the force over a distance of 5.0 m. What is the work done by the force?
EV E Math Initial Final K, + U, + U, - W- K, - Ug+ Uy Usr + AEtherm +. t= 0.80 s ti3=D0 y= 0.70m 0- 7777 to Earth 0. Earth Mbarbell = 13.6 kg 8. The weightlifter, not in the system, raises a barbell. Energy Conservation Equation Show al Civitwar politics.. docx a At Home Friction.pptx IMG_1490jpg 2:43 PM 12/9/2020 T|||||||| ||||||| 2|||||1|1 ||L|||||| 1|||||||| 1|||||||| ||||||
On your bike, you start from rest and accelerate to the speed of 5 m/s in 20 s (assume constant acceleration), and keep going at this speed on a level ground for further 500 m. During your trip, the average air drag force on you is 13 N, and the rolling friction force is 9 N. Assume 75 kg total mass of yourself and the bike, 20% mechanical energy efficiency in your body, and a BMR of 100 W. How much Calories you have spent to accomplish this? Draw the energy model of the situation! k Hint: "Average air drag force" means that you can use the same value of the air drag over the whole travle distance, for both acceleration stage and motion with a constant speed. We know that the air drag force in fact depends on speed, but since the average value i you do not need to care about it. Calculat
A 17100 /b airplane is travelling at 360 mph IAS at 10000 ft on a standard day. The airplane's wingspan and average chord are 59.5 ft and 6.4 ft respectively. What is the airplane's TAS (mph, tenth's)? Your Answer: Answer units
A 50-lb cylinder rests against a wall and a plate as The coefficient of friction is the same shown in Fig. at both surfaces of contact with the cylinder. Plot P, the maximum force that may be applied to the plate without moving the plate, as a function of the co- efficient of friction is (0.05 s u, s 0.80). 6 in G B. 30
I included two pictures. Please show me how to approach the problem in the correct manner based on the feedback given. It is okay to completely change the answer if you need to. Please give a reasoning to why the claim is not reasonable and the work needed to back this up.
b. You are tasked with inspecting the rigging to lift a 40,000 lb air conditioning unit. Assuming the load is balanced, using a 4 leg bridle hitch where the sling length is 15 ft with 8 feet of head room between the hook and the load, what would be the estimated tension on each leg of the sling when the load is lifted? What is the minimum Working Load Limit of each sling leg? What is the required sling breaking strength (assume a safety factor of 5)? 15 ft 8 ft 40,000 lbs
Power