Q6: find the transfer function Xo(s)/Xi(s) of the mechanical system shown in Figure (a). Also find the transfer function Eo(s)/Ei(s) of the electrical system shown in Figure (b). Show that these transfer functions of the two systems are of identical form and thus .they are analogous systems R2 k1 by C2 R1 b2 Xo eo ww

Q6: find the transfer function Xo(s)/Xi(s) of the mechanical system shown in Figure (a). Also find the transfer function Eo(s)/Ei(s) of the electrical system shown in Figure (b). Show that these transfer functions of the two systems are of identical form and thus .they are analogous systems R2 k1 by C2 R1 b2 Xo eo ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer all subpart please Asap for like this please all subpart...
4- Design a boost converter that will have an output of 60 V from a 24-V source. Design for continuous inductor current and an output ripple voltage of less than one percent. The load is a resistance of 50 2. Assume ideal components for this design. VL ooooo ip - ^
d) Design (Find the values of the R₁, R2, and C₁) an astable multivibrator circuit to have an output waveform as shown below in the figure (tH = 375µs and t₁ = 125µs). (Assume C₁ = C₂ and R₁ # R₂) and determine the frequency of oscillation and the duty cycle. R1: R2 C1 Q Vcc 4 555 5 C2 10nF I 8 1 3L -OVO tH = 375.0us tL = 125.0us
The buck converter with resistive load has the input voltage of 30[V], the output voltage of 10[V] (constant), and the switching frequency of 40 [kHz]. If the output average power is 25[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
The buck converter with resistive load has the input voltage of 30[V], the output voltage of 10 [V] (constant), and the switching frequency of 30 [kHz]. If the output average power is 25[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
4. circuits
What are combinational circuits? Draw the classification diagram of them
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
please write introduction about Analysis of simple AC Circuits using MATLAB
6. A buck converter is to work from a 48 V input and supply a 15 V output at power levels from 5 W to 100 W. The design is constrained to have L≤ 200 µH, C≤ 22 µF, and fswitch ≤ 100 kHz. What combination of these three will provide the lowest ripple for a 100 W output? What is this ripple value? What ripple will occur for the 5 W output for the same design?
Write the loop equations for a Buck converter in the two modes if the inductance is characterized by a combination of inductance L1 in series with an equivalent resistance r1, filter capacitance is characterized by a capacitor C1 in series with resistance r2. Also assume that the controlled switch has a drop of 0.4V and the freewheeling diode has a voltage drop of 0.65v. Draw the corresponding equivalent circuits in each mode.
Please answer all subpart in short please Asap for like this please Asap all subpart please...