Q5. The bridge circuit in Figure Q5 below is used to monitor temperature using a thermometer. The resistor R4 acts as a thermometer, and the C voltage supply is 18 V. When the bridge is balanced, R4 = 320 2. What is the value of R3? Calculate the resistance R4 vs Vs relation for the 5 iterations of Vs from 0.5 V to 2.5 V

Q5. The bridge circuit in Figure Q5 below is used to monitor temperature using a thermometer. The resistor R4 acts as a thermometer, and the C voltage supply is 18 V. When the bridge is balanced, R4 = 320 2. What is the value of R3? Calculate the resistance R4 vs Vs relation for the 5 iterations of Vs from 0.5 V to 2.5 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Construct the BJT circuit shown in Figure 1 on your project board with VBB = 12V and Vcc= 12V. Given B = 220 vc 12 V R1 3 33 kn Rc 4.7 kn c2 10uF Vo ci 10uF Vi 2N3904 R2 { 10 kn RE 1.2kn Figure 1 2. Compute thevoltage across base, VB and base current, Is for circuit in Figure 1. Show your calculations.
Instructions: Solve for the following parameters
1. A voltage divider provides 1 V output from 5 V input. The maximum output current is 1 mA. The resistors are chosen to provide load regulation of better than 1% over the load current range of 0-1 mA. Find the resistor values necessary for this application. What is the efficiency at full load?
Referencing to the components connected on the breadboard below, draw the equivalent circuit schematic. 24 V R3 • . . o .. • . o o .. R4 • . O O 0 O O o o O o o O. O o o o o O o o o O o o Oooo o o OoO • 0 o o O0 o o o o o 0 Oo O O o o O o
Help me please
its not graded as before rejected
I posted the same question but the value are wrong .. please check.. Ans for v2 and v3 should be 1.2500V & -1.2500V.. 1. Construct the circuit as shown in Figure 1. Set VS1 and VS2 to 5 V. Measure each of node voltages and record that results in Table below.R1= 1kR2= 3.3k R3= 2.2kR4= 4.7kR5= 1.2k Table 4.2: Nodal Voltage Values Parameter (Volts) THEORITICAL V1 V2 V3 V4 Please draw the current flow in arrow in the circuit. Tq
What is the role of resistor R3 in getting the low bias current we are obtaining out of the Widlar source? I don't really know the importance of R3 when looking at the figure. Is it because it controls the amount of current flowing through the transistor?
To extend the useful range of a voltmeter, an additional resistor, Rseries, is placed in series with the voltmeter as shown in the figure. If the internal resistance of the voltmeter is Ri,V, determine the resistance that the added series resistor has to have to extend the useful range of the voltmeter by a factor N. Then, calculate the resistance the series resistor must have to allow a voltmeter with an internal resistance of 1.00 MΩ and a maximum range of 1.00 V to measure potential differences up to 100. V. What fraction of the total 100.-V potential drop occurs across the voltmeter, and what fraction of that drop occurs across the added series resistor?
The thermistors R1 and R4 in the Wheatstone bridge have the following relationship between the resistance e ³ ( ²7 - 17/12) and temperature: RT Roe Where the constants are as follows: Ro = 200 kilo ohms, T = 298 K, B = 4500 K. The circuit parameters are Vs = 6V, R2 = R3 = 797 kilo ohms. What is Vo at T = 50°C? R3 O 5.13 V O 5.57 V O OV -2.566 V R₂
Find the voltage across each resistors. Use the polarities provided in Figure to compute for the voltages R1 1.2kQ R2 2.2kQ SR4 > 5.6kQ D В E + R3 3.3k2 R5 1.8kQ 20V A
The circuit below, you may note, does not match any of the common op-amp circuits. By performing circuit analysis, determine the voltage across the load resistor R5. You may assume that V1 = 3.6 V, V2 = 4.7 V, R1 = 37 kQ, R2 = 62 KQ, R3 = 77 kQ, R4 = 71 kQ, and R5 = 90 kQ. R1 ww V1 + R2 V2 R3 R4 R5 mm D