Q4- The following information is obtained from the strength test carried on concrete cubes of shown sizes casted using potable and questionable water. Is it recommended to use this questionable water for columns and beams concrete mix? Show the calculations and justify your answer. S. Potable water Questionable water No. Load, kN Cube side, Load, kN Cube side, cm cm (Load +10x16) (Load +7x16) 1 955 15.20 777 15.37 933 15.72 743 14.06 3 936 16.05 744 14.54 4 966 15.91 752 15.60 5 947 15.77 733 14.29 6. 944 16.04 745 15.59 2.

Q4- The following information is obtained from the strength test carried on concrete cubes of shown sizes casted using potable and questionable water. Is it recommended to use this questionable water for columns and beams concrete mix? Show the calculations and justify your answer. S. Potable water Questionable water No. Load, kN Cube side, Load, kN Cube side, cm cm (Load +10x16) (Load +7x16) 1 955 15.20 777 15.37 933 15.72 743 14.06 3 936 16.05 744 14.54 4 966 15.91 752 15.60 5 947 15.77 733 14.29 6. 944 16.04 745 15.59 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stem-leaf diagram below shows compressive strength of concrete cubes measured in (Kpa). Determine the median
2. You are an inspector on a job site, inspecting strength tests from a job with a design strength of 4500 psi. A total of 12 tests were performed on concrete from this job; the strength test results (in psi) are shown below. 4520 4840 4190 4960 4720 4890 4620 4290 4390 4680 4550 4620 Is this concrete acceptable?
Considering the data in the table below; Select the cement type suitable for concrete production in cold weather conditions and explain the reasons.
20 The figure below shows relative frequency histogram for 50 concrete cubes classified according to compressive strength of the cubes. While x- axis represents the class midpoints of compressive strength, y-axis represents relative frequency for concrete cubes. Determine the harmonic mean of compressive strength * .of the cubes Relative Frequency Chart 0.45 0.4 0.35 0.3 0.25 능 0.2 7 0.15 0.1 0.05 25.5 35.5 45.5 55.5 Class Midpoints of Compressive Strength Relative Frequency for Concrete Cubes
Working on major construction project that requires considerable amounts of concrete to be used,you are asked to design a concrete mix following the BRE methodology. All the necessary tables forthis can be found in the Appendix. The concrete mix specifications are:o Characteristic compressive strength of 35 N/mm 2 at 28 days.o Failure rate of 2%o Previous control data yielded a standard deviation of 10 N/mm 2o CEM-I 42.5o Air-entraining is not requiredo Maximum water to cement ratio 0.40o Minimum cement content 390 kg/m 3o Required slump 50 mmo Coarse aggregate: Crushed maximum size 20mmo Fine aggregate: Uncrushed with 90% passing 600 μm sieveo Relative density of aggregates: 2.5o Coarse aggregate has 4% moistureo Fine aggregate is dry and has 1.2% absorption.o Volume of the required trial mix: 0.090 m 3Following the BRE step-by-step process estimate the water content of the mix estimate the content of aggregates, provide the estimated mix quantities
I need answer within 20 minutes please please with my best wishes
True or false: Generally speaking, concrete will be priced the same regardless of its designed strength, 4,500 psi concrete will cost the same as 3,000 psi concrete.
Q1/ Cube of concrete 100 mm long pressed with a pressure test of 98 mm length. To determine the correct geometric strain
35.What is the workability of concrete mixtures? How to evaluate it? please quickly thanks !1
A1-What is the bond strength between steel and concrete and how it can be calculated? 2-What is the segregation of fresh concrete? Give its reason and how to control it? V3- What are the advantages of concrete? 3- Discuss the effect of age and curing on the compressive strength of concrete. 5-What are the main purposes of using plasticizer admixtures? 6-What are the main techniques that should be used to reduce heat of hydration in mass