Q4) A metal plate with 10 in wide and 1.5 in thick. Its material has a strength coefficient 20,000 lb/in? and a strain hardening exponent can be considered zero (in hot rolling conditions). Rolls with radius 12 in, the mill can apply a maximum force 400,000 lb and a maximum horsepower around hundreds hp in order to reduce the thickness of plate by the maximum possible draft per one pass (dmax). Calculate (a) dmax , (b) associated true strain, and (c) maximum number of turns of the rolls for the operation.

Q4) A metal plate with 10 in wide and 1.5 in thick. Its material has a strength coefficient 20,000 lb/in? and a strain hardening exponent can be considered zero (in hot rolling conditions). Rolls with radius 12 in, the mill can apply a maximum force 400,000 lb and a maximum horsepower around hundreds hp in order to reduce the thickness of plate by the maximum possible draft per one pass (dmax). Calculate (a) dmax , (b) associated true strain, and (c) maximum number of turns of the rolls for the operation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A punch must cut a hole of 30 mm diameter in a sheet of metal with 2 mm thick. The ultimate shear stress is 55 MPa. Determine the force required for this operation.
What is the magnitude of shear stress generated in shaft of diameter 20 mm when 10 Nm torque is applied on it.
In a single pass rolling bearing process using 510mm diameter steel rollers a strip of width 110mm and thickness 6mm undergoes 20%reduction of thickness. Find the angle of bite
Hi, can you help me solve the attached problem where I am asked to calculate the total force to obtain a component from an initial aluminum bar by using the manufacturing process of cold rolling.
Examples 2 : A tangential force of 300N affected the tangents on the upper surface of a parallel rectangle of 5cm in height and its upper surface area of 25cm so if you know that the base of the shape is not moving. Calculate (1) shearing stress (2) shearing strain (3) the resulting displacement in the direction of the force knowing that the shear modulus of elasticity of the body material is 4.5 * 101º N / m²?
A 1-in diameter hole is to be punched through a 1/8-in thick annealed titanium-alloy Ti-6Al-4V (grade 5, annealed) sheet at room temperature. Estimate the force required for the punching operation. Show your work and list any values you reference/use. Hint: Use the equation F=T*L*Shear Strength
In open-die forging, a disc of diameter 200 mm and height 60 mm is compressed without any barreling effect. The final diameter of the disc is 400 mm. The true strain is
Please show all work!
In a sheet metal of 2 mm thickness, a hole of 10 mm diame- ter needs to be punched. The yield strength in tension of the sheet material is 100 MPa and its ultimate shear strength is 80 MPa. The force required to punch the hole (in kN) is
In a slab rolling operation, the maximum thickness reduction (del hmax) is given by del hmax = μ²R, where R is the radius of the roll and u is the coefficient of friction between the roll and the sheet. If µ = 0.1, find the maximum angle subtended by the deformation zone at the centre of the roll.
15.A 4.50-in-thick slab that is 9 in wide and 24 in long is to be reduced in a single pass in a two-high rolling mill to a thickness of 3.87 in. The roll rotates at a speed of 5.50 rev/min and has a radius of 17.0 in. The work material has a strength coefficient = 30,000 lb/in2 and a strain hardening exponent= 0.15. The roll force is 483,000 lb 583,000 lb 383,000 lb none
Q4: Proof the validity true strain additive feature in compression deformation?