Q4: A balanced three phase (Y-A) system, the delta load connected to a balanced three phase source of stare connection. The apparent power of each phase impedance of the load is 80 KVA with lagging power factor of (0.8). If one of the phase voltages of the source is Van = 200 230 Vms, the angle of VAB is located at (0°), then determine the following: a) Ica (Arms). b) The sequence of this three-phase system? c) VCA (Vms). d) Vbn (Vrms). e) Total average power absorbed by the load.

Q4: A balanced three phase (Y-A) system, the delta load connected to a balanced three phase source of stare connection. The apparent power of each phase impedance of the load is 80 KVA with lagging power factor of (0.8). If one of the phase voltages of the source is Van = 200 230 Vms, the angle of VAB is located at (0°), then determine the following: a) Ica (Arms). b) The sequence of this three-phase system? c) VCA (Vms). d) Vbn (Vrms). e) Total average power absorbed by the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
Please help with this balanced three-phase circuit problem.
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
The Full-looad and No-load of a regulator are 5.2V and 5.3V, respectively. Then the % load regulation is а. 0.1% b. 2.63% C. 1.92% d. 5.3%
There is an installation with two equal triphasic loads of 300 kVA each and a power factor of 0.9 lagging. When connecting a pure reactive element in parallel, the reactive power at the entrance of the installation is 150 kVARS, with a lagging power factor. We can say that: a) A bank of reactors was connected and the fp deteriorated. b) A capacitor bank was connected and the pf deteriorated. c) A bank of reactors was connected and the fp improved. d) A capacitor bank was connected and the pf improved. e) None of the above
Single phasing happens when one phase of a three phase source becomes unavailable. True False
Q2 (a) Three-phase generator consist of three set of single-phase generators, with voltages equal in magnitude but differing in phase angle by 120° apart. (i) Sketch phasor diagram of the three-phase voltages VA, VB and Vc (ii) Plot the three-phase voltages waveform in Q2(a)(i) in single plot.
Q4: Break Down given system into all pass and minimum phase system and highlight the Z-transform of compensating system. You are free to choose the estimated x,y values for the location of the poles and zeros.
A balanced, 3-phase, 346.41 Vrms line voltage source feeds two loads connected in parallel with a 3-phase line with j3ohm/phase impedance.The first load is Y (star) connected and has an impedance of 12ohm/phase.The second load is D (delta) connected and has an impedance of 12ohm/phase.Taking the Van phase voltage as reference: a)Find the current, active power and reactive power provided by the source. b)Find the phase and line voltages on the loads c)Find the phase currents for each load d)Find the active and reactive power in each load. e)Find the active and reactive power loss in the line f)Show whether the total active and reactive power provided by the source is equal to the total active and reactive power in each load and line.
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?