Q3/A/ Two 5-bit numbers (10110 and 10001) are applied to a 5-bit parallel adder. The inputs carry Cin is 1. Determine the sum and output carry.

Q: What system does the emission designation F2D describes? O a. FSK Data O b. Telephone О с. AM TV O…

A: The International Telecommunication union(ITU) uses some codes to describe  signals.  For example :-…

Q: The concept of the state of a dynamic system refer to a .maximum set of variables The root locus is…

A:

Q: Explain, with the aid of a sketch, the Relay.

A: Power system has currents flowing through transmission lines. These current should be within limits.…

Q: explain insulation coordination and write method of insulation coordination

A: We have to explain insulation coordination and write method of insulation coordination.

Q: A No. 10 AWG copper conductor

A:

Q: What is the meaning of the acronym, XLPE? A. EXTRA LOW POLYESTER EQUIPMENT B. CROSS-LINED POLYETHYL…

A: In this we will write about XLPE....

Q: Please answer in typing format

A: The height at which the rotor, or the blades, is installed atop the tower is known as the hub height…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: 3. The __________ is, in essence, a switch which closes for a brief period of time and then open,…

A: 3. The relays is, in essence, a switch which closes for a brief period oftime and then open, closing…

Q: what is error in mesurement system? Also discuss its types

A: Error is the difference between the true value and measured value of the system. Error = measured…

Q: What is sub station

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: Questions focussed on Channel 1. Coaxial cable and optical fibre are two highly engineered wire…

A: The difference between optical fiber and coaxial cable is shown below. BASIS FOR COMPARISON…

Q: Discuss any two types of signalling mode with a neat diagram.

A: two types of signaling mode with a neat diagram

Q: Which sub-atomic part of an atom is used as a fundamental unit of electricity par'icularly when it…

A: 1.answer: C electron  Electron is the fundamental particle which causes current. While remaining…

Q: Can we replace the Fossil Fuels? How?

A: Can we replace the Fossil Fuels? How?

Q: Write an Arduino based code to take input from two switches, if switch one is pressed than glow full…

A: The input is taken from two switches  On pressing switch one, the full spectrum on RGB Led.  On…

Q: What can you say/perspective about National Electrical Code?

A: The National Electrical Code (NEC) was created to protect people and property from the risks posed…

Q: Develop a simple Arduino-based System that will utilize TIMER and LED. Present your answer in the…

A: It is asked to develop a simple Arduino-based System that will utilize TIMER and LED.We need to…

Q: Attach the proper eve

A:

Q: 14.a. Which test can be used to measure splice loss? A. Tensile measurement B. OTDR C. Bit error…

A: In this question,  We need to Choose the correct options.

Q: 2. Explain over modulation.

A:

Q: What NEC article contains a list of the electrical installations that are covered by the NEC?…

A: The NEC (National Electrical Code) is a globally recognized standard for the safe installation of…

Q: Write a paragraph about your hopes and ambitions. In about 100 words

A: Hope and ambitions are the most important part of any human which can include the happiness of…

Q: Define noise in communication systems and mention the different types Note: Please do not…

A: Noise is an unwanted signal which interferes with the original message signal and corrupts the…

Q: In your own words and from your own understanding, avoid plagiarism or copying from the Course…

A:

Q: 3 smallest change in the quantity that will produce the observable change in the reading is called

A: This question is related to instrumentations. It is based on concept of some terms related to…

Q: Explain LVDT with neat sketch.

A: The construction of LVDT is shown in figure. LVDT translates the linear motion into electrical…

Q: The more reliable standard industry signal is

A: In this question we will write about standard industry signal....

Q: the pathway of a cell phone signal from the caller to the receiver

A: In this Question It is Asked to Trace the pathway of a cell phone signal from the caller to the…

Q: 1. Referring to voltage levels, what is EHV a. Extra High Voltage b. Extreme High Voltage c. Extra…

A: The correct answer is:a. Extra High VoltageExtra-high voltage (EHV) refers to voltages in the range…

Q: When is supernode used in a circuit analysis? Provide an explanation.

A: If we have a voltage source in between two nodes then the two nodes are considered as SUPER NODE

Q: A protective put can be used for risk management.   A. TRUE B. FALSE

A: ANSWER      TRUE          A protective put can be used for risk…

Q: In standard architectural site plan symbols, a fire hydrant is indicated by a/an _. A. Dark -field…

A: In this question we need to choose a correct option.

Q: which side is short cct.in short cct. test ? why?

A: Short circuit test: It is one of the method to calculate the series parameters of the transformer's…

Q: A find the defoie ficld (i Gauss law for Sphonilally Symmestmc Jadial eleetric field, Thus Ocndosed-…

A: Gauss's law: This law states that the net outward of normal electric flux through any closed…

Q: NO. 3 In your own words and from your own understanding, avoid plagiarism or copying from the Course…

A: We have to describe the OIL CIRCUIT BREAKER with proper schematic diagram. First we can discuss…

Antenna Array

An antenna array is a group of antennas joined together and arranged in a regular pattern to form a single antenna capable of producing radiation patterns that individual antennas cannot. As the antennas are constructed as an array, sufficient spacing and phase must be given.