Answered: Q34 If the surface tension of water is…

Engineering

Civil Engineering

Q34 If the surface tension of water is 0.06N/m, then the capillary rise in a tube of a diameter 1mm is :(0 = 0°)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G = 11,500 ksi] shaft (2). Tube (1) has a length of L1 = 50 in., an outside diameter of D1 = 2.55 in., and a wall thickness of t1 = 0.160 in. Shaft (2) has a length of L2 = 52 in. and a diameter of d2 = 1.35 in. If an external torque of TB = 520 lb·ft acts at pulley B in the direction shown, calculate the torque TC required at pulley C so that the rotation angle of pulley C relative to A is zero.
Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (i) (ii) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. 20⁰ А μs=0.35 Figure Q2 B
A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G = 11,500 ksi] shaft (2). Tube (1) has a length of L1 = 40 in., an outside diameter of D1 = 2.05 in., and a wall thickness of t1 = 0.120 in. Shaft (2) has a length of L2 = 54 in. and a diameter of d2 = 1.05 in. If an external torque of TB = 580 lb·ft acts at pulley B in the direction shown, calculate the torque TC required at pulley C so that the rotation angle of pulley C relative to A is zero.
Q34 If the surface tension of water is 0.06N/m, then the capillary rise in a tube of a diameter 1mm is:(0 = 0º)
Glycerin flows at 35 m through a 150 mm diameter new wrought iron pipe at a velocity of 3 m/s. It has an absoluteviscosity of 1.50 Pa-s and a specific gravity of glycerin = 1.26.3. Solve for the coefficient of pipe friction
A cube contracts in volume by 0.05% when acted upon by normal uniform pressure of 2x 106 N/m? on all sides. The bulk modulus of its material is (а) 400 MPа (4000 MPa (d) 40000 MPa (b) 40 MPа
Q2)A filament 0.5m long and having a cross-sectional area of 1mm2 was stretched to breaking. If the breaking stress for the filament was found to be 109 Pa, calculate the mass which was hung on the filament to break it. Assuming the filament stretched linearly up to breaking, calculate the amount by which the filament stretched. (Young’s modulus for the material = 6 x 1010 Pa) If the assumption in (b) was justified, what might the material have been? State in one word.
Asap . Determine the roller support reaction
Find the internal forces for the truss shown. Select the appropriate method of solution and show your calculations.
A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G= 11,500 ksi] shaft (2). Tube (1) has a length of L₁ = 48 in., an outside diameter of D₁ = 2.35 in., and a wall thickness of t₁ = 0.160 in. Shaft (2) has a length of L2 = 56 in. and a diameter of d₂ = 1.25 in. If an external torque of TB = 640 lb-ft acts at pulley B in the direction shown, calculate the torque Tc required at pulley C so that the rotation angle of pulley C relative to A is zero. x Answer: Tc= C B TB Tc (2) (1) L2 L₁ lb-ft+ N
Determine the moment deposition reaction in the structure below: