Q3. The system shown consists of 800 m long pipe of 5 cm cast-iron pipe connected into 400m long pipe of 7 cm Riveted Steel pipe, two 45° (k-0.2) and four 90° (k-0.3) flanged long-radius elbows, a fully open flanged globe valve (k-8.5), and a sharp exit into a reservoir. If the elevation at point (1) is 400 m, what gage pressure is required at point (1) to deliver 0.005 m³/s of water at 20°C into the reservoir? 7cm diameter Riveted Steel pipe, 400m-Long Elevation 500m Open Sharp ext Son diameter cast Iron pipe 800m-long

Q3. The system shown consists of 800 m long pipe of 5 cm cast-iron pipe connected into 400m long pipe of 7 cm Riveted Steel pipe, two 45° (k-0.2) and four 90° (k-0.3) flanged long-radius elbows, a fully open flanged globe valve (k-8.5), and a sharp exit into a reservoir. If the elevation at point (1) is 400 m, what gage pressure is required at point (1) to deliver 0.005 m³/s of water at 20°C into the reservoir? 7cm diameter Riveted Steel pipe, 400m-Long Elevation 500m Open Sharp ext Son diameter cast Iron pipe 800m-long

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

water is flowing through a 35cm diameter welded steel pipe (f=0.014) of length 2300m that drains a reservoir under a head of 50m. the pipe has a thickness of 9mm. if the valve at the end of the pipe is closed in 9s. approximately what water-hammer a. 1.667MPa b. 1.567 MPa c. 1.467 MPa d. 1.367Mpa
Q2/A pipe system carries water from a reservoir and discharges it as a free jet, as shown in Fig. I below. How much flow is to be expected through 200-mm diameter steel commercial pipe with the fittin illustrated. Fig.(1) Reservow Datum 30 m -K-0.05 60 m 20 m 60 m B 200-mm Parmas steel commercial pipe throughout 2.90 elbows K-0.40 - 0113 x 10 m²/s p- 999 kg/m³
Discussion: 1. Designa hydraulic circuit to operate the shear as in part B as well as ensuring that the safety interlock on the guard is always operational. 2. Compare between shuttle valve function and two pressure valve function.
Q1: Find the discharge through the pipe if The diameters of sections (1) and (2) are 25 cm and 30 cm respectively. The velocity of water at section (1) is 6 m/s. Determine also the velocity at section (2) D- 3ecm D25 cm 6m/s
For the hydraulic structure shown below check the thickness of the floor at points (A) and (B) by using Lane's method, and then check the structure against piping use (C-5). u/s F.5.L-112.2 vertical gate all Dimensions in meter Flow 110.0 100.5 108,5 107.9 09 ple (1) 108,9 그 106.5 0.5 pe (2)- 106.1
Q2) Calculate The head loss due to friction in The Piping system shown below. The pipe is (15o mm) in diameter and C1som) Long, Passes aflow of Co.13 m/s 15omm 30m 2. 18m
The steel pipe shown carries water from the main pipe A to the reservoir and is 2 inch in diameter and 240 ft long. What must be the pressure in A to provide a flow of 45 gpm? Clevation K00 t Water 7 50 F Open globe valve 90 bends (threaded)- Elevtion 20 fr 2 in galvanizcd pipe
M ll HM- Pipes.pdf d Mechanics Il nework # Pipelines Basim Al-Zaidi e 16, 2021 A 150-m-long commercial steel pipe is to convey 30 L/s of oil (s = 0.9, (submerged discharge) where the difference in elevation of the free liquid surfaces is 2 m (Fig. P8.69). The pipe entrance is flush, and there is a fully-open gate valve in the line. Using only a basic scientific calculator, find the diameter theoretically required. (Hint: It may be easier to try for D than for f in this case.) A basic scientific calculator is here defined to be one that is not programmable and does not have automatic equation solving capabilities. - 0.038 N-s/m) from one tank to another Valve L, e, Q Flush Figure P8.69
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
Q1) Example: Find the velocity at the pipe center. water D-3" 0.0 (stag.) Hg (S-13.6)
Pipes 1,2, and 3 having diameter of 150mm. 200mm and 250mm and leading from reservoir A, B, and C respectively join at a common point. All pipes are new cast iron (C=120) and each is 500m. If the water level in reservoir A is 1.80m than that in B and 4.8m higher than that in C. a) Calculate the discharge in pipe 1.b) The head loss in pipe 2c) The discharge in pipe 3 ** Need asap pls. Thank you.
Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes. Q2 1500m-300mm Q1 В E 300m-450mm 600m-300mm (6) 400m-450mm 600m-250mm 600m-200m Compute the flow in Pipe 4, Q4 [in m³/s]. O none of these O 0.1418 m3/s O 0.0576 m3/s O 0.1006 m3/s O 0.3000 m3/s O 0.1582 m3/s