Q3. A relaxation oscillator is to generate train of pulses that is used to fire a Thyristor circuit in acontrolled rectifier and, it is known that the external capacitor C=0.1uF and firing pulses aretaken across 1200 with the following data of the relaxation oscillator.VBB=15V; ReB=4.7ko;;=0.7; the valley voltage is=0.9V; Ip=10µA; the valley current is=12mA; R81 duringdischarge =900Determine the followings;į. The value of Vp to switch-on the UJT;ii. The range of Rị to switch-on and switch-off the UJT;iii. Frequency of oscillation with drawing;

Answered: Image /qna-images/answer/853ffa66-e840-4bf0-86e7-87ff976acea9.jpg

Q3. A relaxation oscillator is to generate train of pulses that is used to fire a Thyristor circuit in a controlled rectifier and, it is known that the external capacitor C=0.1uF and firing pulses are taken across 120n with the following data of the relaxation oscillator. VBB=15V; ReB=4.7ko;z=0.7; the valley voltage is=0.9V; I,=10µA; the valley current is=12mA; R81 during discharge =900 Determine the followings; į. The value of Vp to switch-on the UJT; ii. The range of R1 to switch-on and switch-off the UJT; iii. Frequency of oscillation with drawing;

Q3. A relaxation oscillator is to generate train of pulses that is used to fire a Thyristor circuit in a controlled rectifier and, it is known that the external capacitor C=0.1uF and firing pulses are taken across 120n with the following data of the relaxation oscillator. VBB=15V; ReB=4.7ko;z=0.7; the valley voltage is=0.9V; I,=10µA; the valley current is=12mA; R81 during discharge =900 Determine the followings; į. The value of Vp to switch-on the UJT; ii. The range of R1 to switch-on and switch-off the UJT; iii. Frequency of oscillation with drawing;

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q.3 The input, Vs and the output, Vo of a diode circuit (assuming ideal diode) are shown 3 SEEU/SKEU 1063 in Figure A.2. Name an application that can produce output as in Figure A.2 (ii) and draw the circuit. S UTM S UTM UTM UTM S UTM S UTM O UTM 8 UTM UTM S UTM S UTM UTM UTM S UTM UTM MB UTM ot UTM UT S UTM B UTM UTM 8UTM (i) aUTM UT 8 UTM UTM UTM M UTM TM S UTM UTM UT MS UTM or (i) UTM Figure A.2 8 UTM UT TM S UTM
A three phase full converter is supplied by a phase voltage V5-120V, 50 Hz. The rectifier supplies a resistive load R=100 Q. Suppose that the average output voltage is 40 % of the maximum possible average output voltage. The delay angle a would be equal to: Select one: O a. 44.42deg O b. 88.42deg O c. 66.42deg O d. 22.42deg TOSHIBA
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
For the given circuit below, it operates on a peak-to-peak input voltage of 104.6 V, F = 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. %3D Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1 D2 ... AC Input Vsec B (source) D3 D4 Load O 7.32 3.83 6.63 O 3.74 eele
(2) In the adjacent circuit, the input signal Vin = F15V is a square wave. Draw the output signal as a function of time on both Vin ends of: (a)- load resistance. (b) Di-zener Vz=6V In terms of behavior, the value of the output voltage is fixed on the drawing, bearing in mind that the diode is made of
Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.
Q/A Full-wave bridge rectifier with (400 Sin (1007) () ૧૦૯ Sinusoidal input has load resistor of (loks2). Sketch Vo and determine the i- 3 pa PIV
Draw a full-wave bridge rectifier circuit (use multisim) connected to a load resistance of 470 N, with input VPP= 29 V. Connect a voltmeter across the load and an ammeter to measure the current through the load. Peak voltage of the output from the graph Average voltage across the load from the voltmeter reading Average current from the ammeter reading Insert the picture of the simulation here
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
Kindly solve all the parts for me
Use Zener diode to design a clipper circuit to obtain the output waveform as shown in the figure below? 6.9 V +25 V Clipper Circuit -15.7 V -25 V
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V