Q3 Block A moves on a roller along inclined surface and be connected by a rope to black 15. Determine the weight of block A required to catise Block B just about to move if the mass of Block (B) is [10] kg and the static coefficient of frictions between Block B and surface is 0.8. m=10kg B₁ SM₁ = 0.8 MA=?? A 045

Q3 Block A moves on a roller along inclined surface and be connected by a rope to black 15. Determine the weight of block A required to catise Block B just about to move if the mass of Block (B) is [10] kg and the static coefficient of frictions between Block B and surface is 0.8. m=10kg B₁ SM₁ = 0.8 MA=?? A 045

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Similar questions

The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The coefficient of rolling resistance between the 30-kg lawn roller and the ground is r=0.1. (a) Determine the force P required to pull the roller at a constant speed. (b) What force P would be needed to push the roller at a constant speed?
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
2. Find the least value of P required to cause the system of blocks to have impending motion to the left. The coefficient of friction is 0.2 under each block. 300 Ib 100 lb 30 °
Arope is attached to the top corner of a 450-N block, passes over a fixed drum, and is attached to another block as shown in Fig. the 450-N block and the floor is 0.30; between the rope and the drum, 0.60. Determine the maximum mass of block B for which no motion occurs. The coefficient of friction between 20° 1.0 m 450 N B -0.6m
Q3 - Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D. Using the coefficients of static friction indicated, determine the following: 1- The smallest force P which can be applied to the cord that causes impending motion. 2- Does block B spill, flip over, or nothing happen? Prove that. 400 mm D B 500 mm HAB=0.1 A P HA=0.3 co
Q3 - Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D. Using the coefficients of static friction indicated, determine the following: 1- The smallest force P which can be applied to the cord that causes impending motion. 2- Does block B spill, flip over, or nothing happen? Prove that. 400 mm DO B A P 500 mm PAB 0.1 MA=0.3
Determine the magnitude and direction of the friction force exerted on the 100-lb block when (a) 0= 15°, (b) 0= 30°. For both parts, let P 120 lb. Draw separate FBDS for each part of the problem. %3D