Q3 (a) A core sample of granite was drilled at 1.5 m length at Muar. Based on the rock core sample as shown in Figure Q3(a), determine the Total Core Recovery (TCR), Solid Core Recovery (SCR) and Rock Quality Designation (RQD).

Q3 (a) A core sample of granite was drilled at 1.5 m length at Muar. Based on the rock core sample as shown in Figure Q3(a), determine the Total Core Recovery (TCR), Solid Core Recovery (SCR) and Rock Quality Designation (RQD).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Samples from sandstone were collected from two different depths (80m and 200m) and triaxial shearing tests were performed to estimate the shear strength parameters. From each depth, two different specimens were tests at distinct isotropic confining pressures and from the experiments the deviatoric stress at failure was assessed. The results from these experiments are summarized in Table 1.1. Table 1.1 – Results of triaxial shearing tests at failure for the sandstone samples collected from different depths (Question 1) Specimen No. q (MPa) at failure Collection оз (MPa) depth (m) 1 80 0.600 3.325 2 80 1.800 8.179 3 200 0.600 5.310 4 200 1.800 11.103 (a) Determine the angle of shear strength and cohesion of the sandstone for each of the two different depths using the Mohr-Coulomb (linear) failure criterion based on total stress principle. (b) During the triaxial test measurements, local strain gauges were attached to the specimens for high quality measurements to be performed. It was…
It is known that a particular deposit of clay has the following shear strength parameters: c' = 15 kPa, o' = 23°; Cu = 10 kPa, cu = 13° A sample of this clay is consolidated in a triaxial cell to an all-round pressure (03) of 250 kPa. The sample is then sheared by increasing 0₁, keeping 3 constant and the drainage valve closed. What is: i) ₁ at failure? ii) Pore water pressure inside the sample at failure? iii) Final values of 0₁' and 03'? iv) Value at failure of Skempton's pore pressure coefficient A?
1) A dry rock weighs 240 grams and has a bulk density of 2.5 grams per cubic centimeter. Whensaturated with pure water at room temperature (T = 25 °C), it weighs 255 grams. At room temperature,specific volume of water is 1.00295E-03 m3/kg. Calculate the porosity of the sample. 2) A cylindrical core sample of 1.5 cm length and 1.2 cm2cross-section has upstream and downstreampressures of 2 atm and 1.25 atm, respectively, during steady state flow of water at 1.00 g/s at roomtemperature. Calculate the permeability of the core. (Water @ 25 °C, viscosity = 1 cp, density of water = 0.997 g/cm3).
There are 2 samples of granite rock from similar sampling site. However, its dimension height and diameter are different, i.e. for sample A is 104mm : 52mm (height : diameter) and sample B 52mm : 52mm. Between sample A and B, which is expected give a higher rock strength. Justify your answer?
A consolidated-drained triaxial test was conducted on an overconsolidated clay sample. The sample failed in test 1 at 01=200 kPa and 03=130 kPa, and in test 2 at o1=400 kPa and 03=290 kPa. Determine the undrained and drained friction angles and cohesion for the assumption that the Skempton's pore water pressure parameter A=0.45. Also, for a CU test on the same soil, determine o1, 1', 03', and excess pore water pressure u for 03=340 kPa.
A consolidated-undrained triaxial test was conducted on a dense sand with a chamberconfining pressure of 138 kN/m2. Results showed that ’ = 24° and  = 31°. Determine thedeviator stress and the pore water pressure at failure. If the sand were loose, what would havebeen the expected behavior? Explain
Question 10 A 50 m run of core drilled horizontally from an underground drift allowed to recover 42 m ofrock core and 38 m of this core was in pieces longer than 100 mm. In the 4 m of recoveredrock core with pieces smaller than 100 mm, 2 meters contained fresh and sharp breaks(fractures).(a) Determine the Rock Quality Designation (RQD) value and the corresponding rock qualitydescription. (b) Describe the limitations of using RQD to evaluate rock quality and make suggestions onhow you can minimize the sources of error.
How could you detect a naturally fractured reservoir? 2 a) Significant mud loss during drilling of some wells b) Well testing of different wells in different parts c) Core observation d) Production behavior of the reservoir
In a slow triaxial test performed on a sand sample, the chamber pressure is 1.5 kg/cm^2 and the deviating stress at failure is 4.5 kg/cm^2. Assuming that the failure envelope of the sand is straight through the origin, determine the angle fi