Q2. Replace the loading acting on the beam with a single resultant force. Determine (a) the force magnitude, F. (b) the horizontal angle of the force, 0. (c) how far the force should be placed from point A on the beam, x. A 60° |--2 -2 m 450 N 4 m 300 N B -3 m 700 N 30° 3000 N·m

Q2. Replace the loading acting on the beam with a single resultant force. Determine (a) the force magnitude, F. (b) the horizontal angle of the force, 0. (c) how far the force should be placed from point A on the beam, x. A 60° |--2 -2 m 450 N 4 m 300 N B -3 m 700 N 30° 3000 N·m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 15 kN/m 13 kN • 7 m

Q: A thin and weightless beam is supported by a pin connection at 4 and by a roller at B (see figure…

Q: )三 Flop nate locm water 10 4s * Assume the cormeetion factor p=1

Q: Question 2 Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and…

Q: 5. A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at…

A: TAB=110 lb

Q: Problem 8.61 8 of 9 Reiew • Part A The two blocks used in a measuring device have negligible weight.…

Q: 3. A load of 150 kN is acting at A on the machine part shown. 150 kN 40 mm Bo 40 mm C a.) When the…

Q: Reaction forces using integration method b) Reaction forces using method of superposition;

Q: Determine the following a. Resultant force at C b. Resultant force at D c. Resultant force at E…

A: Determine the following. a. Resultant moment at A b. Resultant moment at D c. Resultant moment at E

Q: Question 2 Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and…

Q: P. A 2b This beam has a pinned support at the left end at A and a roller at the right cnd at B.…

Q: Q1- The beam shown is subjected to two types of distributed loading. Support A is a pin, support Bis…

A: A beam is a load-carrying component of the building used to resist seismic conditions and overcome…

Q: 1. The resultant of four forces of which 3 are shown in the figure is a clockwise 480 lb-ft couple.…

A: Draw the figure. Let F4 be the fourth force.

Q: с d = 20 mm Al 20 kN 30 kN 15 kN D d = 15 mm B k 6 m 2 m 2 m 4 m 2 m A beam is suspended by a rod (6…

Q: 5-3 Beam AB carries a uniformly distributed load of intensity ωo = 30 N/m as shown in the Figure.…

Q: differential e quation of the deflection Curve (Neglest self. for The Shown beam-columu, darive and…

A: Given For the beam column the load acting is uniformly distributed load of intensity W kN/m over…

Q: A vertical load P is applied at end B of rod BC. (a) Neglecting the weight of the rod, express the…

Q: 8 kN 4 m

Q: Find the internal forces at the point E, if the mass of the cylinder is 10kg and the force in the…

A: Internal Forces They are forces exerted by one part of the observed system on another. It allows…

Q: Determine the shear force, S, in the web at section 1. Provide your answer in newtons (N) to the…

A: The given figure is shown below:

Q: 1. For the beam and loading shown and knowing that the distributed load w can be expressed as a…

A: A cantilever beam is loaded with a parabolic loading, w = kx2, and the span of the beam is 18ft,…

Q: Consider the beam system below. Assume that the 300 N force is able to move anywhere along the beam.…

A: In this question we will basically use the condition of equilibrium to find the reactions on the…

Q: Q.1 EB and DC consists of flexible steel with diameter (d). If the displacement at point C and B are…

Q: Find the force in spring if support A rotate 0.003 rad C.W and C settle 10mm E=200GPA and…

Q: If the beam shown is supported by the fixed wall at B and the rod AC. if the rod has a cross…

A: Using compatibility equations

Q: Question 1) F= 18 kN single load, M=30 kN.m moment and w=14 kN/m distributed load are acting on the…

Q: Calculate the member forces of the loaded structure.

A: According to given data Calculate the member forces of the loaded structure. Given load 60 KN , 40…

Q: Q1.Find the moment of the force about point O 20? F = 60 N 100 mm Q2. The force F acts on the end of…

Q: how full solution

Q: ind the maximum moment of the given load train at point n on the beam given in the figure?

A: to find maximum moment

Q: Q2 Replace the distributed loading by an equivalent resultant force and couple moment acting at…

A: From the above diagram F1 = 12×3×3⇒F1 = 4.5 KNF2 = 6×3⇒F2 = 18 KNF3 = 12×3×3⇒F3 = 4.5 KN

Q: The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of…

A: Given:- The two forces are applied to the end of the boom OA The magnitude of one force = 200 lb The…

Q: Assume that P = 23 kips and L= 5 ft. Determine the reaction force at C. Assume that El is constant…

A: Using method of consistent deformations treating reaction at B as redundant.

Q: AGO .45 m !1.25 m 1.85 m 1.22 m Wo120 IN A weight W' 120 Kl is being supported by steel sections…

A: Given W=120KN Considering E as origin, We will find position vector, then calculate forced…

Q: P (kN) Şekildeki kafes sistemde çubuk kuvvetlerini Basınç-çekme hesaplayınız. durumlarını A B…

Q: Q5 Draw the influence line for (a) the moment at B, (b) the shear at C, and (c) the vertical…

A: A beam with vertical roller support at A such that it resists only moment and horizontal force and a…

Q: 9-5. Determine the reactions at the supports, then draw the moment diagram. The moment of inertia…

A: Given Structure:

Q: Determine the largest force P (to the nearest integer) which can be applied to the cord without…

Q: (a) For the case of no sway, calculate the value of stiffness (K) and distribution factor (DF) for…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Determine the equivalent resultant force and couple moment at point A for the given force system.…

Q: Assume that P = 13 kips and L = 5 ft. Determine the reaction force at C. Assume that El is constant…

Q: Two blocks are supported by a pulley along an incline as shown. The lower block B has a weight of 37…

A: Figure is as shown

Q: F B A d The wagon has a mass of 19.5 kg and centre of mass at G. Both the front and rear wheels are…

Question

Q2.
Replace the loading acting on the beam with a single resultant force. Determine
(a) the force magnitude, F.
(b) the horizontal angle of the force, 0.
(c) how far the force should be placed from point A on the beam, x.
A
60°
|--2
-2 m
450 N
4 m
300 N
B
-3 m
700 N
30°
3000 N·m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

Step 2: Calculation

Step 3: Calculation

Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 300-N force is applied to the handle of the winch as shown. The force lies in a plane which is parallel to the y-z plane and is perpendicular to line AB of the handle. Determine the moments of this force about point O.
Show the steps
Replace the force by its equivalent force-couple system at A. Solve for F and M. Enter positive numbers for both F and MA 240 mm- Answers: A Oc B 35 28° 770 N 830 mm F = i N MA- i N-m M A 240 mm- 28° 35 A B F 830 mm
When the three forces acting on the quarter-circular plate are replaced byan equivalent force-couple system with the force acting at point D, the resultantcouple is zero. Determine P and the angle θ.
Determine the y-intercept of the force system. The answer should be in feet. Indicate if it is below of O or if it is to above of O.
Please solve this exercise except that a new BF bar with a cross section of143 mm2 is added to the system.
A 72 2 (a) 8 W+ W 2 (c) 2 2W+ с W) 2 T 72 30⁰ A beam AB of length 1 and weight w supports a load W at its free end B and is hinged at its end A. A wire CD supports the beam at the mid point C making an angle of 30° with the horizontal. What is the value of tension T in the wire CD? D B W (b) 4 (2W + w) (d) 4 W+ W 2
The solid 34-mm-diameter steel [E = 200 GPa] shaft supports two pulleys. For the loading shown, use discontinuity functions to compute: (a) the shaft deflection vg at pulley B. (b) the shaft deflection vc at pulley C. Assume LAB = 260 mm, LBC = 400 mm, P = 810 N, Q = 480 N. A LAB B LBC Q C
Ans - Normal force is -41.25 kN. Also find moment at C.
Nedd solution
Replace the force and torque systemacting on the rectangular block by a key.Specify the magnitude of the force and the moment oftorque of the wrench, as well as the point where its line of actionintersects the x-y plane.
The top of the folding workbench has a mass of 40 kg with mass center at G. Calculate the magnitude of the force supported by the pin at E. - 670 mm- G. D. 230 mm H. 975 mm E 1070 mm Answers: E = i N