Q2. Put (T) for true sentences and (F) for fouls one of all the following sentences and (correct the fouls sentences): 5) The......... ndary whuangs te mits. 6) Anstormer regulation of ideal transformer is (unity). 7) The eddy currents always tend to flow perpendicular to the flux. 8) The magnetic field intensity is a vector quantity perpendicular to the direction of field density vector. 9) The areas of the hysteresis loop is a measure of heat energy lost per cycle so that choosing the hard magnetic material is better for construction of magnetic circuits.

Q2. Put (T) for true sentences and (F) for fouls one of all the following sentences and (correct the fouls sentences): 5) The......... ndary whuangs te mits. 6) Anstormer regulation of ideal transformer is (unity). 7) The eddy currents always tend to flow perpendicular to the flux. 8) The magnetic field intensity is a vector quantity perpendicular to the direction of field density vector. 9) The areas of the hysteresis loop is a measure of heat energy lost per cycle so that choosing the hard magnetic material is better for construction of magnetic circuits.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.003 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. 1. - 10 cm--- - 20 cm - 15 cm 500 tums 15 cm 15 cm [1.21 A, 0.4 T, 1.2 T]
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
A magnetic circuit has a m.m.f. of 400 AT and a reluctance of 2 x 105 AT/Wb. The magnetic flux in the magnetic circuit is_ mWb. 6 X
A solenoid has a magnetic reluctance of 2.2 x 10-3. It has 300 turns and a core area of 5 sq. cm. What is the flux density when the current flowing is one (1) ampere? a. in terms Sl unit b. in terms of CGS unit
A small single-phase 60 Hz transformer has 10.2 W at no load. The core has a volume of 750 cm3. The maximum flux density is 10,000 G and the hysteresis constant of the core is 0.0005. Using the Steinmetz law on hysteresis loss, find the eddy current loss.
Derive the equation for rms core flux of ideal ac magnetic circuit using Ohm's of magnetic circuits. Explain the result.
B. For the following magnetic circuit, the flux passing through the core is 1.32 mWb, the cross section of the core is 3 cm by 4 cm, the laminated section has a stacking factor of 0.9, and the gap is 1 mm. Determine the flux density in each section. Neglect fringing d N turns Cast iron Air gap Laminated sheet steel
For operation at 60 Hz and a given peak flux density, the core loss of a given core is 1W due to hysteresis and 0.5W due to eddy currents. Estimate the core loss for 400-Hz operation with the same peak flux density.
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
Explain why, when steel is subjected to alternating magnetization energy, losses occur due to bothhysteresis and eddy currents. The core loss in a transformer core at normal flux density was measured atfrequencies of 40 Hz and 50 Hz, the results being 40 W and 52.5 W respectively. Calculate, at a frequencyof 50 Hz, (a) the hysteresis loss and (b) the eddy current loss. Clear and detailed solution.
(a) Explain briefly what is fringing effect and leakage flux. (b) A ferromagnetic core is shown in Figure 1. The depth of the core is 10 cm. The other dimensions of the core are as shown in the figure. By assuming the magnetic leakage to be negligible and relative permeability of the core is 800. Calculate the total reluctance and find the value of the current that will produce a flux of 0.01 Wb. With this current, calculate the flux density at the top of the core 20 cm 40 cm 10 cm, 30 cm 500 turns 30 cm 30 cm Figure 1
Example(6): A magnetic circuit containing an air gap is shown in Figure below. With the dimension as marked, calculate the current in the coil to establish a flux density of 0.6 T in the air gap. The core has the B - H characteristics. Repeat above but correct for fringing and lamination. Consider SF=0.95, FF 1.08 while is as above. 2 mm) A-5cm²