Q2. In a DSB-SC AM system, the carrier is e(t) = 0.5 cos (20000 nt) and the message signal is given by m() = sinc(t) Find and Sketch the frequency domain (spectram) representation of the modulated transmitted AM signal and show the bandwidth of the modulated AM signal. If the modulation scheme is: (a) DSB-TC (b) DSB-SC (c) SSB (d) VSB

Q2. In a DSB-SC AM system, the carrier is e(t) = 0.5 cos (20000 nt) and the message signal is given by m() = sinc(t) Find and Sketch the frequency domain (spectram) representation of the modulated transmitted AM signal and show the bandwidth of the modulated AM signal. If the modulation scheme is: (a) DSB-TC (b) DSB-SC (c) SSB (d) VSB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) A Double-Sideband Amplitude Modulator is shown in fig. 1 V DC cos(2n x 2 x 105t) m(t) v,(1) Σ Figure 1
Subject:communication. Need solution
Q. Choose the correct answer (.. 1. increases as the length of channel increases. (interference, distortion, additive noise, attenuation). 2. 100% modulation is produced in AM when carrier frequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signal amplitude). 3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V. The amplitude of each sideband frequency is 4. A Phase-Locked Loop (PLL) is a feedback circuit consisting of VCO, all of the above). 5. The line connecting the positive and negative peaks of the carrier waveform is called (Peak line, Maximum amplitude, Modulation index, Envelope) 6. Thermal noise power is proportional to (T², 1/T, T, T'2) 7. Which of the following is an advantage of SSB over DSB? (No change in spectrum space, Reduce in spectrum space, Carrier is suppressed, Power is not wasted on the carrier). 8. Which one of the following is not true with respect to SSB signal? (Hard to…
ver is in the side dulation factor m. This emphasis .8. A carrier wave of 500 watts is subjected to 100% amplitude modulation. Determine: (ii) power of modulated wave. (i) power in sidebands Solutien
D E F
a.Find carrier peak amplitude (vc), carrier frequency (fc), message peak amplitude (vm), messagefrequency (fm) and modulation index (m). b.Write the equation of the VAM (t) in time domain. c.Sketch spectrum of the modulated transmitted AM signal and find the Bandwidth of theTransmitted AM signal d.
4. A modulated signal (AM) varies between the maximum values of +18V and -18V, if the carrier has an amplitude of 12V, a) What is the modulation index? b) What is the maximum magnitude of the modulator? c) Sketch the envelope of the modulated wave
In an AM modulator the message signal is m(t) = coswmit+2coswm2t, and the carrier wave is c(t) = Acosw.t. The modulation index is m = 0.5. a) Determine the amplitude of the carrier wave A. b) Determine the expression of the modulated signal with the AM modulation scheme. c) Determine the expression of the frequency spectrum of the AM modulated signal and then plot the frequency spectrum.
For an FM modulator with 48 kHz of frequency deviation. and a modulation signal frequency fm= 8kHz, determine the bandwidth using both the Bessel table and Carson's rule.
I need the answer as soon as possible
c) An audio signal 10sin 27(2000t) amplitude modulates a carrier 20sin 2π(200000t). i) ii) iii) d) How Sketch the amplitude modulated wave. Determine the modulation index? What is the frequency content of the modulated wave? AM broadenet stations. nodated in a 100 KH