Plz answer within 30 min I vill upvote Q2. (i) A switch tail ring counter (Johnson counter) uses the complement of the serial outputof a right shift register as its serial input.(a) Starting from an initial state of 0000, list the sequence of starts after each shift until theregister returns to 0000(b) Beginning in state 00...0, how many states are there in the count sequence of an n-bitswitch tail counter?

Answered: Image /qna-images/answer/2283f57c-753a-400d-a435-c3ddff177956.jpg

Q2. (i) A switch tail ring counter (Johnson counter) uses the complement of the serial output of a right shift register as its serial input. (a) Starting from an initial state 0000, list the sequence of starts after each shift until the register returns to 0000 (b) Beginning in state 00...0, how many states are there in the count sequence of an n-bit switch tail counter?

Q2. (i) A switch tail ring counter (Johnson counter) uses the complement of the serial output of a right shift register as its serial input. (a) Starting from an initial state 0000, list the sequence of starts after each shift until the register returns to 0000 (b) Beginning in state 00...0, how many states are there in the count sequence of an n-bit switch tail counter?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
1. An 8-bit register contains the number 10000110. The serial number 11011011is applied to the input. After 5 shift pulses, what is the number in the shift register? Assume shift right operation 2. A binary number is shifted 5 positions to the left. The number therefore has been 3. A binary number must be divided by 128. How many positions must the number be shifted (and in what direction to achieve this?
the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary.b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SF20-BEC-156.
Q1. Design a circuit of General register organization in which 4 registers are there from R0 to R3. (a) Explain the control word as per the register configuration given above.
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
The 3-bit shift register is shifted five times to the right with the serial input being 1011101. What is the content of the register? (Write your answer using only 0s and/or 1s.)
Write a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and R7 of Bank 3. Also, mention the value of SP register after every PUSH and POP operation. this question is asked in microprocessor and microcontroller
Design and draw a 4-bit register with load control functions specified.(In the process of changing the locations of the output, the zero bit should be replaced with the third bit and the first bit must be replaced with the second bit.)
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the binary number that is equal to 01100 For this circuit:Draw the logic circuit for the datapath.