Q2. For the beam and loading shown below. The allawable flexural stress is 12MPa, allawable shear stress is 825KPa. Determine the max required width (b) in (mm). 2.4 KN 4.8, KN 1m 1m 1m *200 mm*

Q2. For the beam and loading shown below. The allawable flexural stress is 12MPa, allawable shear stress is 825KPa. Determine the max required width (b) in (mm). 2.4 KN 4.8, KN 1m 1m 1m 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: QI: If the beam with T section shown in Figure 1 is subjected to a positive bending moment M.=45 Use…

A: Given M=45Nm bf=82mm hf=20mm hw=20mm bw=30mm

Q: 4 in. 200 kip 3 ft The column is constructed from high-strength concrete and eight A992 steel…

Q: Compute the maximum load P (in kiloNewtons) so as not to exceed the compressive stress of 75 MPa and…

A: To find out the maximum load P that can carry maximum tensile load 100 Mpa and compressive load 75…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

A: A beam is a structural member that is loaded and supported in the direction of its axis and has a…

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: TF1=20, BF1=3x20=60, Tw=20, Dw=8x20=160, TF2=20, BF2=10x20=200, D=a+8a+a=20+160+20 = 200

Q: 225 mm P1=8 P2=10 M1=15 q1=18 6- 2(m) to 1(m) 4.50 (m) 1.50(m) 66 207 mm 225mm

Q: SITUATION II: A reinforced concrete beam has a width of 400mm and an effective depth of 900mm. The…

A: Given: 400 mm width and 900 mm depth Compression bar 4-25 mm dia, tension bars 4-32 mm dia fc=…

Q: Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by…

A: Overhang Beam : Overhanging beam is type of beam in which the beam extends beyond the end support of…

Q: A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of…

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

Q: 225 P,- 8 P,- 10 9- 18 2 (m) 1 (m) 4.50 (m) 1.50 (m)

Q: 1. Draw the shear and moment Diagram of the beam. 2. Determine the maximum compressive stress of the…

A: Given- A continuous beam of total span 12m and subjected to a UDL of 45Kn/m over the entire span.…

Q: о ехceed e in mm. -2 m D

A: hhhhhhfjhuy

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

Q: Determine the maximum bending stress in MPa

A: The given section is a T section. The maximum bending stress is determined using the bending…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: HOW FULL SOLUTION ! *draw FBD *use data given BELOW

Q: The simple beam with overhang carries a uniform load, w=10kN/m and force P=20.38kN. a. determine the…

A: Answer We know that the Maximum Compressive or Tension stress can be calculated using the Bending…

Q: 6. Compute the maximum tensile and compressive bending stress for the simply supported beam with…

A: A we have to determine the maximum tensile and compressive bending stress

Q: Situation 1 | An overhang beam is loaded as shown below. The beam cross-section was built by…

A: As per company's guidelines we can only answer first question Kindly post other questions as…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

Q: A 90mm concrete slab is supported by a beam 7.50m clear span and 1.20m on center. Web dimension and…

A: Given:- 90 mm concrete slabClear span=7.5 mDepth=500 mmWidth=300 mmfC'=21 MPaϕ=0.90Factored…

Q: Situation 1 | An overhang beam is loaded as shown below. The beam cross-section was built by…

Q: Determine the maximum shearing stress on the beam in MPa. 8. Determine the flexural stress, in MPa,…

Q: shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m,…

Q: 3. In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of…

Q: a) What is the distance to centroid (x）? Please enter answer in mm and to 1dp. b) For the same…

Q: P6-5. Sketch the bending stress distribution over each cross section. (a) M P6-5 (b)

A: Two members cross section are shown in the above figure. We have to draw bending stress distribution…

Q: Compute for the shear stress (in MPa) 1.5 m to the right of point A and 50 mm from the top of the…

Q: 225 of 207 225

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 14 MPa.…

A: For the given beam and loading, the minimum width b has to be computed if the flexural stress is not…

Q: For the beam and loading condition, consider section n-n and determine (a) The largest stress in the…

A: Given data:

Q: With an evenly distributed superimposed load of 25 kN/m, a W420 x 85 steel beam is adequately…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: A square steel slab base of area 1m2 is 11

A: follow given the below

Q: HW: For the beam of details shown in Figure, check the bending stress if: 1- Pd=5 kN, PL= 5 kN 2-…

A: Answer To calculate the bending stress using WSD we have Bending stress in concrete fc = M*xIN.A…

Q: Design of Concrete beam A rectangular beam has a width of 375mm and has an effective depth of 450…

A: please look into the solution

Q: In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of 60…

Q: (1)Calculate the maximum bending stress. (2)Compute the maximum web shear stress in MPa. (3)Compute…

Q: Design the steel reinforcement for the uniaxial eccentrically loaded short column shown below, using…

A: Given:- fc' = 28 MPa fy = 420 MPa ex = 150 mm Pn = 2200 Kn

Q: Situation 1 | An overhang beam is loaded as shown below. The beam cross-section was built by…

A: Answer Let us consider that the two channels back to back forms I section as shown below Area of…

Q: maximum flexural stress on the beam in MPa.

A: Given: Simply supported beam with a overhang carrying udl along its entire length. To determine: The…

Concept explainers

Pressure and Stress

Question

Q2. For the beam and loading shown below. The allawable flexural stress is 12MPa, allawable shear stress is 825KPa.
Determine the max required width (b) in (mm).
2.4 KN 4.8, KN
1m 1m 1m
200 mm*

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step by step

Solved in 10 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular beam 350 mm wide is to be designed for an ultimate moment of 750 kNm with f'c = 28 MPa and fy = 415 MPa. The effective depth of the tension bars is 500 mm and 70 mm for compression bars. %D 1. Determine the depth of the stress block if the tensile strain is 0.005 when the concrete crushes at a strain of 0.003. (in mm) (one decimal place) 2. Determine the total amount of tension reinforcement for the given condition above. (in sq.mm) (whole number) 3. Determine the amount of compression reinforcement required. (in sq. mm) (whole number)
225 P= 8 P= 10 9,- 18 H3 2 (m) 1 (m) . 4.50 (m) 1.50 (m)
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b= 4 m, c = 1 m, P = 7 kN, and w = 4 kN/m. P KN w kN/m cm (not scaled) 220 mm bm a m Ra Ri
1. For the given loaded beam shown, a. b. C. d. 40 kN-m B Im Im C 12 kN/m 3 m 2m E 125 -15- 15 145 Sketch the shear and moment diagram. Determine the maximum tensile bending stress in the beam. Ans. Determine the maximum compressive bending stress in the beam. Ans. Determine the maximum horizontal/transverse shear stress in the beam. Ans. dire lengt
Find the max normal stress (?_???) of the beam below.
6-80* A steel shaft is loaded and supported as shown in Fig. P6-80. Determine the maximum allowable value for the axial load P if the maximum shearing stress in the shaft is not to exceed 60 MPa and the maximum compressive stress in the shaft is not to exceed 96 MPa. Figure P6-80 150 mm T= 35 kN m THUS MERRY -P
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
SHOW COMPLETE SOLUTION AND DRAW THE FBD.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.