Q2: water A rectangular gate of dimension I m by 4 m is held in place by a stop block at B. This block exerts a horizontal force of 40 kN and a vertical force of 0 kN. The gate is pin-connected at A, and the 60 weight of the gate is 2 kN. Find the depth h of the water.

Q: Q1) for the given gate find the force and it center of pressure, If H=3m and K=2m. Watre 1.5 m 90 cm

A: The pressure acting on any body submerged body is the force caused due to head of water.For…

Q: A Determine the reaction forces at pin A and soller B (5 pts) 3 N/M 4m/m 4M 8m Answers must include…

A:

Q: For the quarter circle gate BC with a hinge at C, the force P = . . kN to hold the gate stationary…

A:

Q: Problem 3 A 5-m long and 2-m wide gate contains water with a depth of 4 m as shown and is supported…

A:

Q: Unless otherwise stated, take the density of water to be p. = 1000 kg/m and its specific weight to…

A:

Q: 1. Determine the moment at A required to hold the gate as shown. Use yw = 9.81 KN/m³. 2. If there is…

A: γw =9.81 KN/m3 P= 18.46 kPa To find- 1) Moment at A 2) Resultant force due to water on both side…

Q: 6 m/s ter flows through the e at A at 6 m/s. termine the pressure A and the velocity of 3 m water as…

A:

Q: W-S. 45

A:

Q: a. Determine the horizontal component, vertical component, and the resultant of the hydrostatic…

A:

Q: For the quarter circle gate BC with a hinge at C, the force P = .. kN to hold the gate stationary…

A: Since as we know ,in the case of submerged bodies: Horizontal Force = ρgAh- , Symbols have their…

Q: Each gate of a lock is 5m high and is supported by two hinges placed on the top and bottom of the…

A:

Q: • Find: External reactions in x and y directions needed to hold fixed vane. F,+ • Solution: OIS =…

A:

Q: What is the force on the gate and where is it at. Give veritcal distance from surface and slant…

A:

Q: A pipe has an external diameter Do = 0.5 inches and internal diameter Di = .438 inches. Both ends of…

A: The thickness of the pipe is calculated as, t=D0-Di2=0.5-0.4382=0.031 in The ratio of the thickness…

Q: (a) Replace the loading acting on the beam by an equivalent resultant force FR and couple moment…

A:

Q: 2. The center of gravity of the 50-kg spool is at G. A cable wound around the hub of the spool is…

A:

Q: F8-2. Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at…

A:

Q: Calculate the min. External dia of shaft.

A: Power transmitted by hollow shaft at 1200 pm = 450 Kw Allowable shearing stress in the shaft = 60…

Q: 24 kN S KN/m D 3m- 3m→-3m

A:

Q: 300 N 400 N A B 1 m 2 m 2 m

A: To find the forces at b is depends on the equilibrium equations,…

Q: The wall separates water and glycerin (p=120 kg/m^3). Consider a unit width of the rectangular panel…

A: Given- ρ=120Kg/m3d=6ft The diagram is given below-

Q: Gate AB is semicircular and is held by force P at A. Determine the following: (a) A (m²), (b) h (m),…

A: Thank you for the question. As per honour code we have to answer first three subparts since exact…

Q: A rectangular gate 1.2 m by 3 m is inclined 60° with the horizontal. The top of the gate is…

A:

Q: The shear leg derrick is used to haul the m = 200 kg net of fish onto the dock. Assume the force in…

A:

Q: Find the force F just sufficient to keep the quarter circle gate from opening. The gate is uniform…

A:

Q: AB, a rectangular (0.6 mx0.9 m) sluice gate, blocks a liquid with a gravity of 0.79. The weight of…

A: The figure is given:

Q: . A rectangular gate 1.20 m wide rests against a smooth wall at A. It is hinged at B located at 5.2…

A:

Q: 2. Find and draw influence lines of Fed, and the vertical component of Fec. A B D E F 5 m d 6 at 6 m…

A:

Q: Kindly refer to the given figure below. calculate the support reactions at point A,B & C. NOTE: The…

A:

Q: Consider the ¼-circular planar gate hinged below. Its radius is 3 ft and its weight is negligible.…

A: Given: The radius of the circular plane is 3 ft. The specific weight of water is 62.4 lb/ft3.

Q: For the quarter circle gate BC with a hinge at C, the force P = ... kN to hold the gate stationary…

A: Radius=4.5m Widht=5.5m

Q: ne pipe has a mass of 10 kg/m and is fixed to the wall at A. hree forces, F₁ = 310 N, F₂= 430 N, and…

A:

Q: P В r m Water C

A: let Fr is the resultant force which counter the applied force this force is passing through a point…

Q: A circular gate 1.2 m in diameter is inclined at an angle 30 deg. Sea water stands on one side of…

A: Given:Diameter of gate(D)=1.2 mAngle of inclination of gateθ=30°Specific gravity of sea…

Q: 4. The'rectangular gate AB is 3.05 m x 1.22 m in dimension and its pin connected at the point B. If…

A: FBD of the given problem:

Q: Question 3 (c) Using the same problem above. Where will single support be located to hold the gate…

A: As per question, I solved here only Part (C). This question is related to the Fluid Mechanics from…

Q: В 7 m A 2 m 6 m

A:

Q: For the quarter circle gate BC with a hinge at C, the force P = . . kN to hold the gate stationary…

A:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.